Planosol soil sample size for computerized tomography measurement of physical parameters

Tamanho de amostras para a determinação de parâmetros físicos em planossolo por tomografia computadorizada

SOILS AND PLANT NUTRICTION

Planosol soil sample size for computerized tomography measurement of physical parameters

Tamanho de amostras para a determinação de parâmetros físicos em planossolo por tomografia computadorizada

Alceu PedrottiI^*; Eloy Antonio Pauletto^II; Silvio Crestana^III; Paulo Estevão Cruvinel^III; Carlos Manoel Pedro Vaz^III; João de Mendonça Naime^III; Alvaro Macedo da Silva^III

^IUFS - Depto. Engenharia Agronômica, Av. Mal. Rondon, s/n, Campus Universitário - 49100-000 - São Cristovão, SE - Brasil

^IIUFPel/FAEM - Depto. de Solos, C.P. 354 - 96001-970 - Pelotas, RS - Brasil

^IIIEmbrapa Instrumentação Agropecuária, C.P. 741 - 13560-970 - São Carlos, SP - Brasil

ABSTRACT

Computerized tomography (CT) is an important tool in Soil Science for noninvasive measurement of density and water content of soil samples. This work aims to describe the aspects of sample size adequacy for Planosol (Albaqualf) and to evaluate procedures for statistical analysis, using a CT scanner with a ²⁴¹Am source. Density errors attributed to the equipment are 0.051 and 0.046 Mg m^-3 for horizons A and B, respectively. The theoretical value for sample thickness for the Planosol, using this equipment, is 4.0 cm for the horizons A and B. The ideal thickness of samples is approximately 6.0 cm, being smaller for samples of the horizon B in relation to A. Alternatives for the improvement of the efficiency analysis and the reliability of the results obtained by CT are also discussed, and indicate good precision and adaptability of the application of this technology in Planosol (Albaqualf) studies.

Key words: lowland, albaqualf, bulk density, compaction, soil moisture

RESUMO

A técnica da tomografia computadorizada (TC) permite medir a densidade e a umidade de amostras de solo, constituindo uma importante ferramenta na Ciência do Solo. Este trabalho tem como objetivos descrever os aspectos da adequação do tamanho de amostras de um Planossolo e os procedimentos de avaliação e estudos por análise estatística, empregando-se um minitomógrafo computadorizado de raios gama com fonte de ²⁴¹Am. O valor do erro atribuído ao equipamento são 0,051 e 0,046 Mg m^-3, respectivamente, para os horizontes A e B. O valor teórico da espessura da amostra do Planossolo para uso na técnica de TC com fonte de ²⁴¹Am é, aproximadamente, 4,0 cm para os horizontes A e B. Já a espessura ideal de amostras é de aproximadamente 6,0 cm, sendo menor para amostras do horizonte B em relação ao A. Obteve-se boa precisão e adaptabilidade no emprego da TC para estudos de Planossolos.

Palavras-chave: várzea, Planossolo, densidade do solo, compactação, umidade do solo

INTRODUCTION

Lowland soils, varying from flat to smoothly undulated lands and originated under various conditions of draining deficiency (hydromorphic), are found in river and lagoon plains, extend along large areas of the State of Rio Grande do Sul, Brazil (approximately 5,676,100 ha), and represent 22.85% of the state. They are mainly found along the coastline, southeast hillside, central depression and wide plains (Pedrotti et al., 2001).

Lowland soils are significantly diverse regarding mineralogical and morphological characteristics and physical and chemical properties, as a result of heterogeneities of original constituents and different levels of their hydromorphic state, requiring to be grouped in categories of different limitations for agricultural uses (Klamt et al., 1985). Among these soils, the Planosol class comprises the largest area (3,022,500 ha or 56% of the lowland soils), representing around 11% of the total state area (Pinto et al., 1999).

To extend the management of Planosols to other uses, it is necessary to characterize them and evaluate their behavior when submitted to various tillage pratices and potential alternative cropping practices. Among the parameters used to evaluate tillage methods, soil density is one of the most important to characterize and estimate the effects on soil compaction (Pedrotti, 1996). The application of conventional techniques to measure density by gravimetry, volumetric ring, impermeable clod, etc, is limited to non-swelling soils, which is not the case of these hydromorfic soils (Crestana, 1992; Pedrotti et al., 2001).

Computerized tomography (CT) does not disturb natural structure of the samples, having also good sensibility and high resolution. It enables the detection of heterogeneities and extreme values of densities and water content, in a relatively fast, accurate and practical manner (Sposito & Reginato, 1992). The description of this technique, concerning principles, potentialities, operational aspects, methodology, methods of image reconstruction and nuclear radiation can be found in Crestana (1985), Cruvinel (1987), Vaz (1989), Aylmore (1993), Chieppe Jr. (1993), Cássaro (1994), Naime (1994), Anderson & Hopmans (1994), Biassussi (1996), Pedrotti (1996) e Pedrotti et al. (2001).

Because of interactions between the ionizing radiation (gamma or X-ray beams) and the soil sample constituents, absorption or attenuation occurs with part of the incident radiation, i.e., a number of photons passes through the sample without interacting, and another part totally or partially transfers energy to the sample. Lambert-Beer's law relates I_o, the count of incident photons per second (cps), I (cps) of the emergent beam, sample thickness x (cm) to calculate the linear attenuation coefficient - LAC or m_l (cm^-1):

This coefficient depends on various parameters, and the most relevant are: the radiation energy (source feature), the atomic number of the sample components and the density of the absorber (soil). Once the energy of the radiation to be used and the material to be analyzed are defined, m_l is only a function of sample density (r):

where m_m (cm² g^-1) is the mass attenuation coefficient (MAC). In the soil, m_l depends on the relative composition of the different chemical elements within the sample and on the water present in the pores. Eq. 03 enables the calculation of both density and water content of a soil sample analyzed by attenuation:

where: m_m-m (cm² g^-1) is the MAC of solid part (soil); m_m-l (cm² g^-1) is the MAC of liquid (water) and q (cm³ H₂O cm^-3 soil) is the volumetric water content of the sample (Pedrotti, 1996).

CT can be used to measure density and porosity, which is related to the level of compaction and to the water content of soil samples of irregular shape. It is thus necessary to know the MAC for each soil type. Measurement errors can also be minimized with the selection of adequate sample sizes. One of the factors that can be used to verify optimal conditions of the equipment is the evaluation of the standard deviation values of measurements obtained with the CT scanner (Ferraz & Mansell, 1979).

This work aims to establish procedures to optimize regular sample sizes and evaluate statistical procedures to utilize an X and gamma ray CT miniscanner, for density measurements of horizons A and B of a Planosol (Albaqualf).

MATERIAL AND METHODS

Soil characteristics

Soil samples were collected in an experiment of irrigated rice under different cultivation systems, managed since 1985, at Capão do Leão, RS, Brazil, where the control plot (soil not submitted to farming) was chosen. The area is located in the physiografic region of the coastline of the south of the Rio Grande do Sul State (31°52'00''S, 52°21'24''W; average altitude 13.2 m). The soil consists of high activity clay, medium clay texture, a tipical lowland soil (Pedrotti et al., 2001) classified as a Hydromophic Eutrophic solodic Planosol (Pinto et al., 1999) corresponding to a solodic Planosol (Brasil, 1986) and an Albaqualf (Soil Survey Staff, 1990).

Twenty five structured samples were collected by the hydraulic structured soil sampling method – HSSSM (Pedrotti et al., 1994), using 100 mm diameter PVC pipes for depths 0-30 cm. Samples were sealed with paraffin and their spatial orientations or the field profile marked. Subsequently, they were cut in different heights to attend the objectives of the present work. Some disturbed samples were collected and used for the calibration of the CT miniscanner.

Description of the equipment

A first generation CT miniscanner was used, configured as a ²⁴¹Am gamma ray source (energy 59.6 keV and activity 300 mCi); one NaI (Tl) scintillation crystal detector coupled to a photomultiplier and a preamplifier base; amplifier, discriminator, pulse counter and a computer. Resident softwares controlled the scanning mechanism, the nuclear counting system and mathematically reconstructed tomographic images (Cruvinel, 1987). Gamma-ray beams were obtained from two 20 mm-long collimators with 4 mm diameter orifices (Crestana, 1985; Cruvinel, 1987; Cruvinel et al., 1990; Crestana et al., 1992; and Vaz et al., 1992), one placed in front the source and the other in front of the detector (Figure 1).

To establish the ideal soil sample size for CT, it is necessary to calibrate the equipment at minimum error conditions, obtained by statistical evaluation. The calibration was made by a linear regression between tomographic units (TU, obtained from the image reconstruction program) and the linear attenuation coefficients, measured by direct transmission (20 replicates per each material), using aluminum, benzine, water and sieved samples of air-dried Planosol, froms horizons A and B (30 replicates per horizons).

Soil density values by CT

Scannings were performed for 11 hours in each selected cross section. Images were reconstructed (Cruvinel, 1987) from an attenuation data file. A tomographic image represents a map of TU values calculated for each pixel (4 mm x 4mm). The image is formed by the linear assignment of TU to 16 grayscale values, white representing the highest attenuation value and black the lowest (air). An example of a tomographic image is shown in Figure 2.

Selection of the ideal sample size for a Planosol

The most significant sample dimension for CT scanning is the thickness x (cm) crossed by the radiation beam. For each horizon of the Planosol, x was calculated by equation (04) as proposed by Ferraz (1974) using the radiation energy of Americium (59.6 keV). Respectively, m_m-s e m_m-l correspond to soil and water mass attenuation coefficients (MAC), r to soil bulk density (Mg m^-3) and q to the volumetric water content (m³ m^-3):

For the calculation, average density values were determined by volumetric rings and average soil water contents by the gravimetric method.

Sample size optimization was carried out with 5 samples of thicknesses 20, 40, 60, 80 and 100 mm. Image reconstruction provides a file of bidimensional maps of TU values. Soil density values were calculated averaging 90 pixels (6 x15 pixels) for each sample. To find the proper sample size (which leads to minimum error in parameter evaluation), the standard deviation values, coefficients of variation and errors were applied in associated form, for each thickness, each horizon, according to Ferraz (1974) and Miyazaki et al. (1991). The optimum thickness band was selected by the minimum values of the set of parameters. The product: m_m-s . x < 1 was also used in the evaluation, because it is an indication of the ideal condition (Ferraz, 1974).

RESULTS AND DISCUSSION

To optimize sample size allied to the condition of minimum error, it is necessary to obtain precise density values, and to have accurate tomographic measurements of density and moisture, values of MAC have also to be precisely determined. Table 1 shows the average MAC (m_m) values for horizons A and B of the Planosol and for other materials, with their respective standard deviations and the theoretical value for water. Water, a homogeneous medium, presented the lowest standard deviation values, and that indicates the good precision of the measurements. These results are function of the collimation and count rates, close to the ideal condition reported by Appoloni & Cesareo (1994).

According to Ferraz & Mansell (1979), horizons rich in Fe and Ca compounds and mineral clays contribute to raise MAC values. These authors reported that values lower than those presented in their work, point to bad collimation and detection procedures. In addition, high standard deviations may indicate not only heterogeneity of samples, but also insufficient number of measurements or low intensity of radiation beams. Further information on the influence of soil chemical composition on MAC values can be found in Reginato & Van Bavel (1964). Soil heterogeneity, particle size distribution (texture) and composition itself may also constitute error sources. In these cases, a great number of measurements becomes necessary.

The theoretical value of LAC for most soils is 0.25 cm^-1 (Ferraz, 1974). To obtain preliminarily values of LAC, a 7.5 cm thickness was assumed to be crossed by the energy beam; LAC values obtained for horizons A and B were relatively close to the ideal (Table 1). When compared to theoretical values, it can also be seen that the ideal thickness is close to the attained value.

The calibration of the miniscanner was made through the linear regression between LAC and TU for different materials (Table 1 and Figure 3), according to Crestana et al. (1986; 1996):

Admitting homogeneous soil chemical composition and including the contribution of water content, we have:

In equation (06), TU is the average value of each scanning line (average of 5 pixels or columns), taken from the tomographic map generated for each sample. To minimize variations of TU values, an option is the increase of the number of columns (pixels in line). However, when showing distinct regions of the central column is desired the whole tomographic map must be observed to get discrepant values and variables that may reveal heterogeneities.

With the results of MAC and the calibration line the following equations were obtained to calculate densities of the Planosol:

Sample size optimization

The theoretical, ideal sample thickness was estimated to be 4.4 and 3.8 cm, respectively for horizons A and B (Eq. 04). These values come near to those found by Ferraz & Mansell (1979) at 60 keV, and point the importance of the determination of the ideal sample size, previously and approximately admitted to be 7,5 cm, to minimize errors. The good results obtained are attributed to the high beam intensity (20.200 photons/minute), higher than 10,000 photons/minute, recommended by Ferraz (1974), and a consequence of the choice of an adequate source activity and collimation geometry between source and detector (156 mm), always recommended to be as close as possible.

The ideal thickness of soil samples not only depends on water content and bulk density, but mainly on their mass attenuation coefficients, which depend on total porosity and on soil chemical composition (Ferraz, 1974). Table 2 shows soil bulk density values obtained at positions between 2 and 10 cm along the height of the sample. The ideal thickness band was selected within the range of 4 to 6 cm, by the combination of the lowest standard deviation values, coefficients of variation and percentage error relative to five chosen sample sizes (Table 2), (Ferraz, 1974). Results agree with various authors cited by Ferraz (1974) and Appoloni & Cesareo (1994), assuming the criterion "m₁ . x" always < 1. This product determines the magnitude of the incident beam besides influencing the contrast quality of the resulting image. The acceptable value of the product m₁ . x is between 1 and 6, corresponding, respectively, to attenuation between 65.0 and 99.7% (Appoloni & Cesareo, 1994).

When analyzing bulk density, water content and porosity of horizons A and B of a Planosol, through CT (Table 2) recommended sample thickness show come near 6.0 cm. This value is consistent, because it is within the interval obtained with Eq. 04. The ideal thickness of horizon B should be somewhat smaller than horizon A, since the subsurface horizon presents higher values for LAC, meaning a higher beam attenuation as compared to horizon A. This difference results from the chemical and textural composition of the horizons. As a consequence, it can be assured that for horizon B error values are higher as compared to horizon A, even for the same thickness crossed by the beam. Therefore, it is very important to define the optimal thickness, especially for the low energy of the ²⁴¹Am radiation, according to Ferraz & Mansell (1979).

The optimal thickness values obtained for the Planosol samples are very close to those found by Miyazaki et al. (1991), for sandy soils of Japan, also using a ²⁴¹Am source and a similar equipment configuration, and by Ferraz & Mansell (1979) for Fe- and organic matter-rich soils of São Paulo State, Brazil. For these soils, the authors recommend maximum error values similar to those found herein. Considering the 60 keV energy of ²⁴¹Am and the optimal condition for thickness between 4 and 8 cm for most Brazilian soils, the first step to reduce errors in the measurement of bulk density and moisture by CT, is the precise and accurate determination of MACs.

CONCLUSIONS

The ideal sample thickness for physical parameters analysis of a Planosol for CT measurements, using the energy of 60 keV (²⁴¹Am), is approximately 6.0 cm, 20% lower for horizon B in comparison to A. For best results, the free beam count should be over 10,000 photons/second. Furthermore, source and detector should be well collimated, parallel to the cross section plane and the detector as close as possible to the source.

ACKNOWLEDGMENTS

To staff of the Laboratory of Soil Physics and from Soil Department of FAEM-UFPel, Embrapa Clima Temperado (Capão do Leão-RS), and Embrapa Instrumentação Agropecuária (São Carlos- SP). Also for the financial support of DS-FAEM, FAU, UFPel, FAPESP (projects 9013773-7 and 12.094.093.00).

Received May 27, 2002

Accepted August 17, 2003

References

• ANDERSON, S.H.; HOPMANS, J.W. (Ed.) Tomography of soil-water-root process Madison: SSSA, 1994. 148p.
• APPOLONI, C.R.; CESAREO, R. Microscanning and microtomography with X-ray tubes Roma: CISB-Universitá degli Studi di Roma "La Sapienza", 1994. 84p. (RAP, 04.94)
• AYLMORE, L.A.G. Use of computer-assisted tomography in studyng water movement around plant roots. Advances in Agronomy, v.49, p.1-53, 1993.
• BIASSUSSI, M. Estudo da expansão e contração de um vertissolo através da tomografia computadorizada simultânea. Pelotas: UFPel/FAEM, 1996. (Dissertação - Mestrado)
• BRASIL. Ministério das Minas e Energia. Projeto RADAM Brasil: Folha SH.22 Porto Alegre e parte das folhas SH.21 Uruguaiana e SI.22 Lagoa Mirim. Rio de Janeiro, 1986. (Levantamento de Recursos Naturais, 33).
• CÁSSARO, F.M. Tomografia de dupla energia para caracterização físico-hídrica de meios porosos deformáveis sob diferentes graus de hidratação. São Carlos: USP/IFSC, 1994. (Dissertação - Mestrado)
• CHIEPPE Jr., J. B. Estudo e comparação de diferentes métodos de determinação da umidade do solo em laboratório. Botucatu: UNESP/FCA, 1993. (Dissertação -Mestrado)
• CRESTANA, S. A tomografia computadorizada como um novo método para estudos da física da água no solo. São Carlos: USP/IFQSC, 1985. (Tese - Doutorado)
• CRESTANA, S. Noninvasive measurements. In: SPOSITO, G.; REGINATO, R.J. Opportunities in basic soil science research Madison: SSSA, 1992. p.83-85.
• CRESTANA, S.; CESAREO, R.; MASCARENHAS, S. Using a computed tomograph miniscanner in soil science. Soil Science, v.142, p.56-61, 1986.
• CRESTANA, S.; CRUVINEL, P.E.; VAZ, C.M.P.; CESAREO, R.; MASCARENHAS; S.; REICHARDT, K. Calibração e uso de um uomógrafo computadorizado em ciência do solo. Revista Brasileira de Ciência do Solo, v.16, p.161-167, 1992.
• CRESTANA, S.; CRUVINEL, P.E.; MASCARENHAS, S.; BISCEGLI, C.I.; MARTIN NETO, L.M.; COLNAGO, L.A. (Ed.) Instrumentação agropecuária: contribuições no limiar do novo século. Brasília: EMBRAPA, SPI, 1996. 291p.
• CRUVINEL, P.E. Minitomógrafo de raio X e raio gama computadorizado para aplicações multidisciplinares. Campinas: UNICAMP/FEE, 1987. 325p. (Tese - Doutorado)
• CRUVINEL, P.E.; CESARIO, R.; CRESTANA, S.; MASCARENHAS, S. X and g ray computerized minitomograph scanner for soil science. IEEE Transactions on Instrumentation and Measurement, v.39, p.745-750, 1990.
• FERRAZ, E.S.B. Deterninação simultânea da densidade e umidade de solos por atenuação de raios gama do ²⁴¹Cs e ²⁴¹Am. Piracicaba: USP/ESALQ, 1974. 120p. (Tese - Livre Docência)
• FERRAZ, E.S.B.; MANSELL, R.S. Determining water content and bulk densiy of soil by gamma ray attenuation methods Gainesville: University of Florida, 1979. 51p. (Technical Bulletin, 807).
• KLAMT, E.; KAMPF, N.; SCHNEIDER, P. Solos de várzea no estado do Rio Grande do Sul. Porto Alegre: Universidade Federal do Rio Grande do Sul, Faculdade de Agronomia, Depto. de Solos, 1985. 43p. (Boletim Técnico de Solos, 4).
• MIYAZAKI, T.; KASUBUCHI, T.; HASEGAWA, S. A statistical approach for prediting accuracies of soil properties measured by single, double and dual gamma beams. Journal of Soil Science, v.42, p.127-137, 1991.
• NAIME, J.M. Projeto e construção de um tomógrafo portátil para estudos de ciência do solo e plantas, em campo. São Carlos: USP/EESC, 1994. 87p. (Dissertação - Mestrado)
• PEDROTTI, A. Avaliação da compactação de um Planossolo submetido a diferentes sistemas de cultivo. Pelotas: UFPel/FAEM, 1996. 96p. (Dissertação - Mestrado)
• PEDROTTI, A.; PAULETTO, E.A.; BIASSUSI, M.; TURATTI, A.L. Método de amostragem indeformada para diferentes estudos na ciência do solo. In: Reunião Brasileira de Manejo e Conservação do Solo e da Água, 10. Florianópolis, 1994. Resumos Florianópolis: SBCS, 1994. p.326-327.
• PEDROTTI, A.; PAULETTO, E.A.; GOMES, A.S.; TURATTI, A.L.; CRESTANA, S. Sistemas de cultivo de arroz irrigado e a compactação de um Planossolo. Pesquisa Agropecuária Brasileira v.36, p.709-715, 2001.
• PINTO, L.F.S.; PAULETTO, E.A.; GOMES, A.S.; SOUSA, R.O. Caracterização de solos de várzea. In: GOMES, A.S.; PAULETTO, E.A. (Ed.) Manejo de solo e da água em areas de várzea Pelotas: Embrapa Clima Temperado, 1999. p.11-36.
• REGINATO, R.J.; Van BAVEL, C.H.M. Soil water measurement with gamma attenuation. Soil Science Society of America Proceedings, v.28, p.721-724, 1964
• SOIL SURVEY STAFF. Keys to soil taxonomy 4.ed. Blacksburg, 1990. 422p. (SMSS Technical Monograph, 6).
• SPOSITO, G.; REGINATO, R.J. Opportunities in basic soil science research Madison: SSSA. 1992. 109p.
• VAZ, C.M.P. Tomografia computadorizada aplicada a estudos de compactação de solos. Piracicaba: USP/ESALQ, 1989. 110p. (Dissertação - Mestrado)
• VAZ, C.M.P.; CRESTANA, S.; REICHARDT, K. Tomografia computadorizada na aAvaliação da compactação do solo. Revista Brasileira de Ciência do Solo, v.16, p.153-159, 1992.

Publication Dates

• Publication in this collection
  24 Oct 2003
• Date of issue
  Dec 2003

History

• Accepted
  17 Aug 2003
• Received
  27 May 2002