Abstracts
We investigate the estimation of fractures orientation, strike and dip, through multiazimuthal AVO analysis of qP and its converted waves qS1 and qS2. We assume weak impedance contrast, weak anisotropy and that the fractured medium behaves as an effective transversally isotropic (TI) medium. Under these assumptions, the estimation of fractures orientation is reduced to the estimation of the orientation of an axis of symmetry from qP reflectivity data. Linearized approximations of qP reflectivity are used for inversion.
Anisotropy; fractures orientation; Multiazimuthal AVO
Investigamos a estimativa da orientação de fratura; mergulho e direção, através da análise de AVO multiazimutal de ondas qP e de suas convertidas qS1 e qS2. Assumimos fraco contraste de impedância, fraca anisotropia e ainda que, o meio fraturado comporta-se efetivamente como um meio transversalmente isotrópico (TI). Dentro destas hipóteses, a estimativa da orientação de fratura reduz-se a estimativa da orientação do eixo de simetria a partir de dados de refletividade de ondas qP. Aproximações lineares da refletividade da onda qP são utilizadas na inversão.
Anisotropia; estimativa da orientação de fratura; AVO multiazimutal
Estimation of fractures orientation from qP reflectivity using multiazimuthal AVO analysis
Ellen N. S. GomesI; Jessé C. CostaII; João dos S. ProtázioIII; Ivan A. Simões FilhoIV
IDepartamento de Matemática, Campus de Castanhal - Universidade Federal do Pará (UFPA), Rua Augusto Correa, nº 1, Bairro do Guamá, CEP: 66075-900, Belém-PA. Departamento de Geofísica. Fax: 91-3183-1693, Tel: 91-3183-1692. E-mail: ellensg@ufpa.br
IIDepartamento de Geofísica - Universidade Federal do Pará (UFPA), Rua Augusto Correa, nº 1, Bairro do Guamá, CEP: 66070-110, Belém-PA. Fax: 91-3184-1693, Tel: 91-3184-1692. E-mail: jesse@ufpa.br
IIIDepartamento de Matemática - Universidade Federal do Pará (UFPA), Rua Augusto Correa, nº 1, Bairro do Guamá, CEP: 66075-900, Belém-PA. Departamento de Geofísica. Fax: 91-3183-1693, Tel: 91-3183-1692. E-mail: protazio@ufpa.br
IVGaffney, Cline and Associates. 1360 Post Oak Blvd. suite 2500. Houston, TX 77056.Tel +1-713-850-9955. Fax +1-713-850-9966 E-mail: iadsf@attglobal.net
ABSTRACT
We investigate the estimation of fractures orientation, strike and dip, through multiazimuthal AVO analysis of qP and its converted waves qS1 and qS2. We assume weak impedance contrast, weak anisotropy and that the fractured medium behaves as an effective transversally isotropic (TI) medium. Under these assumptions, the estimation of fractures orientation is reduced to the estimation of the orientation of an axis of symmetry from qP reflectivity data. Linearized approximations of qP reflectivity are used for inversion.
Keywords: Anisotropy, fractures orientation, Multiazimuthal AVO.
RESUMO
Investigamos a estimativa da orientação de fratura; mergulho e direção, através da análise de AVO multiazimutal de ondas qP e de suas convertidas qS1 e qS2. Assumimos fraco contraste de impedância, fraca anisotropia e ainda que, o meio fraturado comporta-se efetivamente como um meio transversalmente isotrópico (TI). Dentro destas hipóteses, a estimativa da orientação de fratura reduz-se a estimativa da orientação do eixo de simetria a partir de dados de refletividade de ondas qP. Aproximações lineares da refletividade da onda qP são utilizadas na inversão.
Palavras-chave: Anisotropia, estimativa da orientação de fratura, AVO multiazimutal.
INTRODUCTION
Most hydrocarbon reservoirs occur in fractured formations. In this case, fractures mainly control the reservoir permeability. Since wave propagation in fractured media might be modelled through an effective anisotropic medium (HUDSON, 1982; SCHOENBERG; SAYERS, 1995), the characterization of the reservoir elastic anisotropy from seismic data may help optimizing oil recovery. Previous works report fractures characterization from AVO/AVD data. Rüger and Tsvankin (1997) show how to estimate vertical fractures strike and fluid content information from qP reflection coefficients data. Perez e outros (1999) use shear wave splitting and P wave reflection data to determine the strike of a vertical set of fractures. Beretta, Bernasconi and Drufuca (2002) use diffraction tomography to estimate the fractures density also for vertically fractured medium. We formulate the problem of fractures characterization using the reflections coefficients of a qP incident wave, including converted waves.
FORWARD PROBLEM
Consider weak impedance contrast and weak anisotropic media separated by a plane interface, x3 = 0. The incident and reflected waves propagate at the upper medium and the transmitted waves propagate through the lower medium. The linearized qP reflectivity across an interface was presented by Gomes e outros (2001). The two anisotropic media are considered as small perturbations around an isotropic homogeneous background. The linear approximations are:
Where q is the incidence angle; j is the azimuth angle; k = a / b is the ratio between S-wave and P-wave velocities in the isotropic reference medium; rº is the background density; Dr is the average density contrast across the interface;
is the average elastic constants contrast across the two media defined for
Where indicates the transmission medium elastic tensor and
is the elastic tensor in the medium of incidence, i, j = 1, ..., 6in the standard reduced notation (HELBIG, 1994). The equations (1) was presented previously by Vavrycuk and Psencik (1998) and the equations (2) and (3) where also derived in Jílek (2002) in a somewhat different form. In order to derive the expression above, the polarization directions in the background media were chosen to be the SV and SH direction, which makes them more suitable when the medium of incidence has azimuthal symmetry. However, if degenerate perturbations theory can be used to compute more suitable polarization directions for shear waves (JECH; PSENCIK, 1989).
INVERSION PROBLEM
Using the equation (1) - (3) the inversion problem is reduced to the solution of a linear system:
Where r is the vector containing the observations , p is the vector containing the density and elastic parameters contrasts and the matrix A(C0, j, q) depends only on the background medium and the directions of the incident qP wave.Based on SVD analysis of A, multiazimuthal data is required to produce stable estimates . 3-D VSP experiments (LEANEY; SAYERS; MILLER, 1999) might provide this kind of data. The vector p is organized as bellow:
For estimate of the parameters p we assume:
weak impedance contrast, weak anisotropy;
the medium of incidence is isotropic and coincides with the background media used for linearization.
For the estimation of fractures orientation we assume that the fractured medium behaves as an effective TI medium with its axis of symmetry perpendicular to the plane of fractures.
Under these assumptions, our goal is to estimate the orientation of the symmetry axis from the elastic parameters estimated from inversion. If the axis of symmetry is not aligned with one of the coordinate axis the plane of symmetry containing the axis forms an angle Y with the x3 (Figure 1). This angle can be determined from the relation:
Unfortunately two angles have the same tangent Y and Y + p/2. Rotating the elastic parameters estimated by the negative of one of these angles aligns the symmetry plane containing the tilted axis along the x1 or x2 axis. We can always choose the rotation, which align the symmetry plane containing the tilted axis along the x1 axis and use the expression below to determine the dip angle Q
Under our assumptions, dip angle can be estimated from the inversion results except by the same ambiguity as before, i.e.,Q or Q + p/2. This ambiguity can be resolved rotating the parameter by the negative of these values and observing the differences C11 C22 and C33 C22. If the first difference is zero the axis of symmetry is aligned along x3 and the dip angle is Q + p/2 otherwise C33 C22 is zero and the axis is aligned along x1 and the dip angle is Q. It is always possible to perform this rotation, all the combination of elastic parameters required to perform this rotation are estimated from inversion. If the axis of symmetry coincides with one of the coordinate axis the algorithm fails. In this case orientation can be determined using the alternatives:
The resolution and stability of the inversion was evaluated using SVD analysis and numerical simulations. For the simulations several synthetic data sets were computed using the exact expressions for the reflection coefficients. Each synthetic data set was contaminated by Gaussian noise using 100 random seeds to initialize the random number generator. These data were inverted and the mean and standard deviations of the parameters used to evaluate stability.
EXAMPLES
The elastic parameters and the orientation the axis symmetry was estimated the of inversion from (1), (2) and (3) joins for two models. The synthetic data set was generated solving the Zoeppritz equations (GOMES, 1999). The azimuth range is from 0º to 360º with 15º intervals and the incidence angle varies from 0º to 30º with 1º intervals. This data set was contaminated with different level Gaussian random noise of amplitude of 5% to 20% of the mean absolute value of the observations. The 100 data sets, each with a different noise contamination, were inverted. Both models have weak contrast Dr/r, Da/a, Db/b are smaller than 10% and weak anisotropy.
In the first model the top medium is an isotropic r = 2.65g/cm3a = 4.00km/s e b = 2,31km/s. The bottom medium is TI with horizontal axis and its density is p = 2.5g/cm3 and its elastic tensor is:
Table 1 presents the average and standard deviations of the numerical simulation results,
The parameters DC11, D(C12 + 2C66), D(C13 + 2C55), DC22, D(C23 + 2C44), DC33, DC44, DC55 and Dr/rº presented a relative error lower then 15% which characterizes a stable estimation. The remaining parameters, p9 p20, have very small mean (10-4) and the relative error cannot be computed. These results holds for data noise level lower than 20%. We must use (9) in order to estimate the orientation of the symmetry axis. The difference between C22 and C33 is smaller than the difference between these parameter and C11. Noticing also the difference between C44 and C55, we conclude the medium is TI with horizontal axis. The results are the same for 20% noise level.
In the second model the top medium is isotropic r = 2.60g/cm3, a = 4.600 km/s and b = 2.810km/s. The bottom medium is a sandstone, its elastic tensor is TI with vertical axis and its Thomsen parameters (THOMSEN, 1986) are r = 2.50g/cm3, a = 4.476km/s and b = 2.841km/s, e = 0.097, d = 0.091, g = 0.051. This medium was rotated of 60º anticlockwise around x3 axis and after that rotated of 30º anticlockwise around the new x2 axis (see Figure 1).
The Figures 2(a), 3(a), 4(a) present the stereogram of the exact synthetic data for each wave type. Figures 2(b), 3(b), 4(b) present the corresponding stereogram computed from the mean of the parameters estimated from 100 numerical simulations.
The symmetry of the RPP stereogram indicates its insensitivity to the dip of fractures. However, the SVD shows that RqPqP data is required to estimate the fractures dip. The estimated models fit the data with maximum residual of the order of 10-3 for every data set. The results of the numerical simulations for this model for 10% noise level are presented in Table 2 which shows for the exact value of the p, its the average of the estimated, the ratio of the of the standard deviations. The results of the numerical simulations for this model for several noise levels are presented in Table 3 the of the average of the estimates of the symmetry axis azimuth and dip and the ratio of the standard deviation of the estimation over their average value.
The SVD analysis and the relative error of the estimated parameters in numerical simulations show that, although parameters D14, D15, D16, D24, D25, D26, D36, D45, D46, D56 present instability, the estimates of the symmetry axis orientation is stable. Since the recovery of the orientation depends on nonlinear functions of the parameters SVD analysis can not be applied to determine stability.
CONCLUSIONS
Several tests were performed with models with weak impedance contrast and weak anisotropy and also with models that violated some of these assumptions. Also different azimuth rages and incidence angles were used. From these test we drew the following:
1. RqPqP,
and
are required to recover the orientation from multiazimuthal AVO data only.
2. The minimum azimuth interval to recover stable estimates of orientations is j = 30º.
3. The minimum incidence angle range is q = 30º.
4. Though the estimates of elastic parameters contrasts vary during the simulations, the estimates of the orientation angles are reliable for moderate noise levels (<10%).
5. The estimates of fractures strike is more sensitive to noise than the fractures dip.
6. The estimates are accurate only for models with weak impedance contrast and weak anisotropy.
We presented an algorithm to estimate fractures orientation using multiazimuthal AVO analysis. Reflection coefficients of RqPqP, and
are needed to determine the fractures dip. Though the assumption of an effective TI behavior for fractures is restrictive, its validity can be checked from the symmetries of the elastic tensor derived from the inverted parameters. For a weak TI medium and weak impedance contrast, the estimates of fractures orientation are unique and stable for moderate noise levels.
Acknowledgments
The authors acknowledge the financial support of the Project FINEP/CTPETRO/UFPA.
Recebido em 3 jun., 2002 / Aceito em 5 dez., 2003
Received Jun 3, 2002 / Accepted Dec. 5, 2003
NOTES ABOUT THE AUTHORS
Ellen de Nazaré Souza Gomes é formada em Licenciatura Plena em Ciências com Habilitação em Matemática (Universidade da Amazônia-Belém/PA,1990). Mestrado em Matemática (Universidade Federal do Pará-UFPA/1999) e Doutorado em Geofísica (UFPA/2003). É Professora da Universidade Federal do Pará desde 1997, no Departamento de Matemática, Campus de Castanhal. Atualmente é Professora do Departamento de Geofísica desta mesma Universidade. Áreas de interesse: anisotropia e modelagem sísmica.
Jessé Carvalho Costa é formado em Física (UFPA/1983) Mestre e Doutor em Geofísica (UFPA/1987, 1993 respectivamente). Summer Student na Schlumberger Cambridge Research em 1991 e 1992. Estágio de pós-doutoramento no Departamento de Geofísica na Universidade de Stanford (1994-1996) e Visiting Assistent Professor no Departamento de Geofísica da Universidade de Stanford (1995). É professor da Universidade Federal do Pará desde 1989, no Departamento de Física, de 1989/2003. Atualmente é professor do Departamento de Geofísica desta mesma Universidade. Áreas de interesse: anisotropia, modelagem sísmica e tomografia.
João dos Santos Protázio é formado em Matemática (UFPA/1972). Mestre em Matemática (PUC-RJ/1976). Doutor em Geofísica (UFPA/1994). Estágio de pós-doutoramento no Departamento de Matemática na Universidade Estadual de Campinas-UNICAMP. Foi pesquisador no Laboratório Nacional de Computação Científica - LNCC (1985-1987). Foi professor auxiliar e assistente na Pontifícia Universidade Católica do Rio de Janeiro - PUC (1973-1979). Foi professor da Universidade Federal do Pará, de 1973-2003. Atualmente é professor e coordenador do Curso de Licenciatura em Matemática da Escola Superior Madre Celeste-ESMAC. Áreas de interesse: anisotropia, modelagem sísmica.
Ivan A. Simões Filho é Geólogo pela Universidade de Nancy (França) e Doutor em Geofísica pela Universidade Federal da Bahia (UFBA). Foi professor de Geofísica de Reservatórios da Universidade Estadual de Campinas (UNICAMP) entre 1992 e 2003, onde coordenou o Programa de Pós-Graduação em Geoengenharia de Reservatórios e foi coordenador Associado do Centro de Estudos do Petróleo. Entre 1998 e 2002 foi superintendente de Promoção de Licitações da Agência Nacional do Petróleo (ANP) e entre 1999 e 2003 foi vice-presidente da Sociedade Brasileira de Geofísica (SBGf). Desde 2003 é Associado Sênior da Gaffney, Cline & Associates (GCA), uma empresa de consultoria internacional em petróleo e gás natural. Membro da SBGf, IBP, SEG, EAGE e AAPG, publicou vários trabalhos em revistas científicas e técnicas no Brasil e no exterior e orientou vários alunos de pós-graduação. Fluente em português, inglês, francês e espanhol, Ivan reside atualmente em Houston (Estados Unidos), de onde coloca sua experiência à disposição dos clientes da GCA em projetos de petróleo e gás natural em diversos países das Américas, África, Europa, Oceania e Oriente Médio.
- BERETTA, M. M.; BERNASCONI, G.; DRUFUCA, G. AVO and AVA inversion of fractured reservoir characterization. Geophysics, [S.l.], v. 67, n. 1, p. 300306, 2002.
- GOMES, E. N. S. Reflectivity of P waves in anisotropic media. Thesis (Master)-Department of Mathematics, Universidade Federal do Pará, Belém, 1999. In portuguese.
- ______ et al. Linearization of qP wave reflection coefficients in anisotropic media. Brazilian Journal of Geophysics, [S.l.], v. 19, n. 1, p. 4860, 2001. In portuguese.
- HELBIG, K. Foundations of anisotropy for exploration seismics Oxford: Pregamon, 1994. (Handbook of Geophysical Exploration, v. 22)
- HUDSON, J. A.Wave speeds and attenuation of elastic waves in material containing cracks. Geophys. J. R. astr Soc, [S.l.], v. 64, p. 133150, 1982.
- JECH, J.; PSENCIK, I. First-order perturbation method for anisotropic media. Geophys. J. Int., [S.l.], v. 99, p. 369376, 1989.
- JÍLEK, P. Converted PS-wave reflection coefficients in weakly anisotropic media. Pure and Applied Geophysics, [S.l.], n. 7-8, p. 15271562, 2002.
- LEANEY,W. S., SAYERS, C. M.; MILLER, D. E. Analysis of multiazimuthal VSP data for anisotropy and AVO. Geophysics, [S.l.], v. 64, n. 4, p. 11721180, 1999.
- PEREZ, M. A., GIBSON, R. L.; TOKSOZ, N. Detection of fracture orientation using azimuthal variation of P-wave AVO responses. Geophysics, [S.l.], v. 64, p. 12531265, 1999.
- RÜGER, A.; TSVANKIN, I. Another perspective on AVO crossplotting. The Lead Edge, [S.l.], v. 16, n. 9, p. 12331237, 1997.
- SCHOENBERG, M.; SAYERS, C. Seismic anisotropy of fractures. Geophysics, [S.l.], v. 60, p. 204211, 1995.
- THOMSEN, L. Weak elastic anisotropy. Geophysics, [S.l.], v. 51, n. 10, p. 19541966, 1986.
- VAVRYCUK, V.; PSENCIK, V. PP-wave reflection coefficients in weakly anisotropic elastic media. Geophysics, [S.l.], v. 63, n. 6, p. 21292141, 1998.
Publication Dates
-
Publication in this collection
18 Jan 2007 -
Date of issue
Dec 2002
History
-
Received
03 June 2002 -
Accepted
05 Dec 2003