jaos
Journal of Applied Oral Science
J. Appl. Oral Sci.
1678-7757
1678-7765
Faculdade De Odontologia De Bauru - USP
Bauru, SP, Brazil
O presente estudo avaliou o efeito da força de aperto de parafusos de retenção na desadaptação marginal de próteses sobre implantes. A investigação foi conduzida baseada em resultados fornecidos por nove estruturas metálicas implanto-suportadas de seis elementos (02 retentores e 04 pônticos), retidas por parafusos. A mensuração da desadaptação marginal foi realizada com auxílio de microscópio óptico, nos seguintes momentos: M1: aperto com chave manual até a primeira resistência do parafuso; M2: aperto utilizando torquímetro mecânico com 10Ncm e M3: aperto utilizando torquímetro mecânico com 20Ncm. As médias de desadaptação foram submetidas à análise estatística (ANOVA e Tukey). O emprego de torquímetros mecânicos, independente do valor de torque, determinou redução significativa na abertura marginal (p<0,05). A desadaptação média na interface conexão/prótese em M1 foi de 41,56µm (DP±12,45µm). O emprego do torquímetro de 10Ncm (M2), reduziu 52% desta fenda marginal, para uma média de desadaptação de 19,71µm (DP±2,97µm); enquanto o torquímetro de 20Ncm (M3) reduziu 69% da desadaptação marginal, para uma média de 12,82µm (DP±4,0µm) os de retenção de próteses implanto-suportadas tem importante efeito na mensuração da desadaptação marginal, uma vez que pode modificar consideravelmente as aberturas na interface conexão/prótese.
ORIGINAL ARTICLES
The influence of different screw tightening forces on the vertical misfit of implant-supported frameworks
Avaliação do efeito da força de aperto de parafusos de retenção na desadaptação marginal de próteses sobre implantes
Diego Klee de VasconcellosI; Marco Antonio BottinoII; Renato Sussumu NishiokaIII; Luiz Felipe ValandroI; Elza Maria Valadares da CostaI
IDDS, MSc, PhD, Graduate Student (PhD degree), Department of Dental Materials and Prosthodontics, UNESP São Paulo State University "Júlio de Mesquita Filho" - São José dos Campos Dental School
IIDDS, MSc, PhD, Associate Professor, Department of Dental Materials and Prosthodontics, UNESP São Paulo State University "Júlio de Mesquita Filho" - São José dos Campos Dental School
IIIDDS, MSc, PhD, Assistant Professor, Department of Dental Materials and Prosthodontics, UNESP São Paulo State University "Júlio de Mesquita Filho" - São José dos Campos Dental School
Correspondence
ABSTRACT
OBJECTIVES: The present in vitro study was designed to compare the differences in the vertical misfit of implant-supported frameworks using three different forces for tightening the bridge locking screws: fastening by hand until first resistance, and using torque drivers with 10 and 20Ncm.
METHODS: The investigation was conducted based on the results given by 9 six-unit nickel-chromium (2 abutments/ 4 pontics) screw-retained implant-supported frameworks. The structures were exposed to simulated porcelain firings. The marginal misfit measurements were made using a traveling measuring microscope at selected screw tightening forces: fastening by hand until first resistance, and using torque drivers with 10 and 20Ncm. The results were submitted to one-way ANOVA with repeated measures on one factor, and post hoc pairwise comparisons using Tukey test (5%).
RESULTS: The mean marginal misfit of the frameworks, fastening the screws by hand until first resistance, was 41.56µm (SD±12.45µm). The use of torque driver devices caused a significant reduction in marginal opening (p<0.05). With the lowest torque available (10Ncm), the mean marginal discrepancy at the abutment-framework interface was reduced an average of 52% to a mean marginal opening of 19.71µm (SD±2.97µm). After the use of the 20Ncm torque driver, the mean marginal discrepancy of the frameworks was reduced an average of 69% to a mean marginal opening of 12.82µm (SD±4.0µm). Comparing the use of torque drivers with 10 and 20 Ncm torque, the means are not significantly different from one another.
CONCLUSION: The seating force has an important effect on the vertical misfit measurements, once it may considerably narrow the vertical misfit gaps at the abutment-framework interface, thus leading to a misjudgment of the real marginal situation.
Uniterms: Dental implants; Osseointegration; Implant-supported dental prosthesis; Torque, misfit.
RESUMO
O presente estudo avaliou o efeito da força de aperto de parafusos de retenção na desadaptação marginal de próteses sobre implantes. A investigação foi conduzida baseada em resultados fornecidos por nove estruturas metálicas implanto-suportadas de seis elementos (02 retentores e 04 pônticos), retidas por parafusos. A mensuração da desadaptação marginal foi realizada com auxílio de microscópio óptico, nos seguintes momentos: M1: aperto com chave manual até a primeira resistência do parafuso; M2: aperto utilizando torquímetro mecânico com 10Ncm e M3: aperto utilizando torquímetro mecânico com 20Ncm. As médias de desadaptação foram submetidas à análise estatística (ANOVA e Tukey). O emprego de torquímetros mecânicos, independente do valor de torque, determinou redução significativa na abertura marginal (p<0,05). A desadaptação média na interface conexão/prótese em M1 foi de 41,56µm (DP±12,45µm). O emprego do torquímetro de 10Ncm (M2), reduziu 52% desta fenda marginal, para uma média de desadaptação de 19,71µm (DP±2,97µm); enquanto o torquímetro de 20Ncm (M3) reduziu 69% da desadaptação marginal, para uma média de 12,82µm (DP±4,0µm) os de retenção de próteses implanto-suportadas tem importante efeito na mensuração da desadaptação marginal, uma vez que pode modificar consideravelmente as aberturas na interface conexão/prótese.
Unitermos: Implantes dentários; Osseointegração; Prótese dentária fixada por implante; Torque, desadaptação.
INTRODUCTION
Implant restorations can be either screw or cement-retained. Screw-retained designs have a well-documented history of success. Implant biomechanics investigations have focused on this kind of restoration, which is designed to provide predictable retrievability and abutment-restorative joint integrity 9,18.
An accurate fit between the implant abutment and the superstructure in screw-retained implant prostheses is very important. Poorly fitting implant frameworks can potentially cause uneven thread contact, tension, and bending stresses of the connecting screw, therefore resulting in screw loosening and fractures, and marginal peri-implant bone loss 3. These problems are induced by static forces caused by the tension in the bridge locking screws when securing a misfitting framework to the implants 12.
The seating force used to place the frameworks on the abutments may have an important effect in vertical measurement investigations. A large range of seating forces has been used in previous fit studies 3,23,28, but no optimal value has been proposed. The use of torque drivers to tighten the superstructure screws, even with the lowest torque available (10Ncm) using the manufacturer's torque driver, may considerably narrow the vertical misfit gaps at the abutment-to-cylinder interface. In vitro studies have shown that vertical gaps may be closed by flexure in the framework and anchorage unit components when the bridge locking screws are tightened to the correct preload level 12,17,21.
This significant decrease in the marginal opening from screw tightening is associated with higher stress in screw-retained restorations leading to a misjudgment of the real marginal situation and substantially increasing the fatigue of the components, resulting in loosening or fracture of the prosthesis or abutment screws, distortion or breakage of the restoration, and marginal peri-implant bone loss 9,28.
The present in vitro study was designed to compare the differences in the vertical misfit of implant-supported frameworks using three different forces for tightening the bridge locking screws: fastening by hand until first resistance, and using torque drivers with 10 and 20Ncm.
MATERIALS AND METHODS
The condition simulated for evaluation in this study was a mandibular anterior quadrant to be restored with a six-unit FPD screw-retained on implants. An acrylic resin model (Figure1) was fabricated with two external hex cylinder implants (4.0 mm diameter, 15.0 mm length; Master Screw Conexão Sistemas de Prótese São Paulo, Brazil) placed in the right and left canine area (sites 33 and 43), parallel and 22mm apart from each other from center to center. This model served as an index for marginal misfit measurements. Abutments were connected to the implants (Micruscone 138023 Conexão Sistemas de Prótese São Paulo, Brazil) by fastening screws with a torque wrench using 20Ncm torque. Impression posts (141000 Conexão Sistemas de Prótese São Paulo, Brazil) were attached to the abutments, and a silicone impression (Express 3M São Paulo, Brazil) was made using a custom resin tray suitable for the master cast. After the impression posts and the abutment analogs (143000 - Conexão Sistemas de Prótese São Paulo, Brazil) were connected, they were returned to the impression, which was poured in stone (Durone Dentsply Petrópolis, Brazil) to make the working cast.
Ten implant-supported frameworks were fabricated on the working cast. For fabrication of standardized wax pattern for the FPD, the castable plastic cylinders (149001 Conexão Sistemas de Prótese São Paulo, Brazil) were placed on the analogues and hand tightened until resistance was felt. Teeth were fashioned in inlay wax in an anatomically correct manner. A condensation silicone mold (Express 3M São Paulo, Brazil) was fashioned over this FPD wax pattern to allow for multiple FPD pattern replications.
The investment, burnout and casting techniques were standardized. Patterns were sprued and invested in pairs in a phosphate-bonded investment (Belavest SH Bego Bremen, Germany) according to a 1-piece casting technique. Following bench curing and burnout, the investment rings were cast in a nickel-chromium alloy (Wironia - Bego Bremen Germany).
Divesting was completed in the usual manner with minimum use of aluminum oxide air abrasives on critical interfaces. Burs were used under laboratory microscope to eliminate internal casting inaccuracies. Protective polishing caps (abutment analogues - 143000 - Conexão Sistemas de Prótese São Paulo, Brazil) covered the interfaces and reduced the risk of inaccuracy. In this occasion, one FPD was discarded because of casting problems.
Nine frameworks (Figure 2) were exposed to six simulated porcelain-firing cycles (two opaque firings, three body firings, and one glaze firing). However, porcelain was not applied. All samples were allowed to cool to room temperature before the next firing cycle began.
The marginal misfit measurements were made using a traveling measuring microscope (Sprint 100 - RAM Optical Instrumentation Irvine, CA - USA). Six marks were made in each abutment to standardize the microscope measurement points. Three were made on the buccal surface and three on the lingual surface, adding up to twelve reading points for each framework. The frameworks were positioned on the abutments of the acrylic resin model by fastening titanium screws, always by the same investigator, using three different forces for tightening the bridge locking screws:
1. Using a hand-operated screwdriver (060300 - Conexão Sistemas de Prótese São Paulo, Brazil) until the screws started to offer resistance, based on tactile sensation;
2. Using a mechanical torque-controlling device with 10Ncm (400000 - Conexão Sistemas de Prótese São Paulo, Brazil);
3. Using a mechanical torque-controlling device with 20Ncm (400000 - Conexão Sistemas de Prótese São Paulo, Brazil).
Measurements were made for the three different torque moments. The marginal gap size was measured in micrometers under 230x magnification (Figure 3). Data were analyzed to determine the mean marginal openings and standard deviations for each of the 9 FPD using the three different tightening forces. The results were submitted to RM ANOVA and Tukey test (5%).
RESULTS
The mean marginal misfits of the frameworks (in micrometers), using the three different forces for tightening the bridge locking screws, are summarized in Table 1. The mean marginal opening, fastening the screws by hand until first resistance, was 41.56µm (SD±12.45µm). Upon screw tightening using torque driver devices, margins closed significantly (RM ANOVA, Fdf (2; 16) = 49.40; p = 0.001). With the lowest torque available (10Ncm), the mean marginal discrepancy at the abutment-framework interface was reduced an average of 52% to a mean marginal opening of 19.71µm (SD±2.97µm). After the use of the 20Ncm torque driver, the mean marginal discrepancy of the frameworks was reduced an average of 69% to a mean marginal opening of 12.82µm (SD±4.0µm). Comparing the use of torque drivers with 10 and 20 Ncm torque, the means are not significantly different from one another (Figure 4).
DISCUSSION
The seating force has an important effect on the vertical misfit measurements, since it may considerably narrow the vertical misfit gaps at the abutment-framework interface 9,12,28. Few studies have attempted to correlate implant prostheses misfit related to different seating forces used to place the samples on the abutments before microscope measurements. A large range of seating forces has been used in previous fit studies 3,23,28, but no optimal value has been proposed.
When two components are tightened together by a screw, this unit is called a screw joint. The clamping force needed to keep the components tightly together under static and dynamic conditions is called preload 1,22. When the prosthesis does not make complete contact with the abutment, there will be a gap between all or part of the matching surfaces. If there is no contact, the preload is used to bring the matching surfaces closer together, and perhaps into contact. In this situation, virtually no fatigue protection is obtained because any external load applied to separate the prosthesis from the abutment causes further tension in the screw and is not dissipated by relieving compressive stresses in the clamped parts, resulting in screw loosening and fractures 3,13,28. The introduction of a 100mm discrepancy in the in vitro model results in a change in the external preload (the static axial force and bending moment acting between the implant and the prosthetic construction due to misfit) of approximately 200N per abutment 21.
In the present investigation, microscopic evaluation of the marginal discrepancy was used to determine whether differences existed between three screw tightening forces (fastening by hand until first resistance, and using torque drivers with 10 and 20Ncm) used to place the frameworks on the abutments, prior to the microscope measurements. Measurement data were obtained by positioning the samples under the microscope so that the marginal area of the implant-restoration junction was viewed from a directly perpendicular perspective. Other investigators 10,14,15,28 have also used this methodology. It allows the measurement of marginal discrepancy in a nondestructive format with multiple readings on the samples. Although there are many ways to assess three-dimensional fit of prostheses to abutments, the sophisticated testing equipment required for such testing is not readily available 10,12. The use of more common measuring techniques still provides information on the relative fit or misfit of prosthesis while recognizing the fact that this is not as precise as the other methods 10.
The results of this investigation showed that the use of a torque driver, even with the lowest torque available (10Ncm), may considerably narrow the vertical misfit gaps at the abutment-framework interface. Mean marginal opening, fastening the screws by hand until first resistance, was 41.56µm (SD±12.45µm). Screw tightening using torque driver devices caused a significant closure in the mean marginal openings (p<0.05). With the lowest torque available (10Ncm), the mean marginal discrepancy at the abutment-framework interface was reduced an average of 52% to a mean marginal opening of 19.71µm (SD±2.97µm). After the use of the 20Ncm torque driver, the mean marginal discrepancy of the frameworks was reduced an average of 69% to a mean marginal opening of 12.82µm (SD±4.0µm). Comparing the use of torque drivers with 10 and 20 Ncm torque, the means are not significantly different from one another. There seems to be a positive relation between the torque used for tightening the screws and the amount of vertical discrepancy. The results of this study compared favorably with prior studies evaluating marginal adaptation 9,12,14,17,28.
Using a 3-D photogrammetric technique to measure distortion of 3-unit implant frameworks and bone surrounding osseointegrated implants, other investigators 12 showed that the mean displacement of the frameworks, measured in the direction of the long axis of the cylinder, was 177µm (range from 100 µm to 300µm). These levels of distortion are higher than the levels reported in this investigation using comparable screw preload. However, variations in framework stiffness, as well as in positions of the implants in the different studies, may well explain these differences. The authors also identified a vertical movement of the implant head up towards the framework, of a mean magnitude of 123µm (range 60µm to 200µm). Consequently, by considering both the flexure of the metal frame, as well as the bone strain, they assumed that gaps, even wider than 100µm, could somehow be closed in clinical situations by means of tightening the bridge locking screws.
In the present investigation, the vertical movement that narrows the marginal gaps probably occurred because of the displacement of the frameworks in the direction of the cylinder, since the index model used as an implant receptor for this in vitro study was fabricated using a thermo-activated acrylic resin that does not have the same flexural behavior as the human bone. The mean displacement of the frameworks measured in the direction of the long axis of the cylinder was 21.85µm after the use of the 10Ncm torque-controlling device, and 28.74µm after the use of the 20Ncm torque-controlling device.
The accuracy with which persons can achieve a specified torque (10, 20 and 32Ncm) on the appropriate implant component with hand-held screwdrivers has been examined 3,8,22. The investigators found a wide variation in the ability of clinicians to perceive torque. These studies indicated the unsteady torque that hand-held screwdrivers may apply. The results observed in the present study support the fact that marginal misfit investigations, in which screws are fastened by hand, always by the same investigator, until the first resistance is met 27,28, allows a more real fit evaluation, since no attempt is made to narrow the vertical misfit gaps. However, it seems to be a risky protocol, due to the difficulty in standardizing the screw tightening procedure prior to microscope measurements 3, 22, 25. The fabrication of a special torque driver to reduce the lower torque, as previously suggested 23, may standardize the screw tightening without considerable influence on the vertical misfit gaps. Future research may be directed towards evaluation of this method.
The popularity of base metal alloys (nickel-chromium and cobalt-chromium) has dramatically increased in recent years because of their advantageous mechanical properties and due to the high cost of gold and palladium. The superior yield strength (resistance to permanent deformation), and higher elastic modulus (rigidity) allow a more uniform stress distribution within the framework, providing a more efficient and durable load transfer. The use of a more rigid material for the framework of osseointegrated prosthesis decreases the stress within the prosthesis retaining screws. This probably means that the high resistance of the framework to bending reduces the risks of mechanical overloading for the retaining screws, especially for the cantilevered superstructures 20,26.
Based on previous articles 5,11,16,19,28, which indicated a certain biological tolerance for prosthetic misfits in the living bone, the vertical gaps recorded in the present study, using torque drivers with 10 and 20Ncm, would probably not be clinically distinguishable, and would not lead to clinical problems, even with the frameworks being fabricated by a one-piece cast method instead of the soldering method which would markedly improve the marginal fit 15,24,27.
Previous investigations found that porcelain application had no effect on casting distortion 2,4,6,7; thus, the presence of the ceramic would not modify the results of the present research.
Stress introduced into the implant system as a result of prosthesis misfit may be present many years after placement. This observation supports the concern for the precision of frameworks with regard to various aspects of fatigue in the long-term perspective. Accurate, reliable, and verifiable methods to improve and precisely evaluate fit are still needed.
CONCLUSION
The seating force has an important effect on the vertical misfit measurements. The results of this investigation showed that the use of a torque driver, even with the lowest torque available (10Ncm), may considerably narrow the vertical misfit gaps at the abutment-framework interface. This significantly decrease in the marginal opening from screw tightening is associated with higher stress in the screw-retained restorations leading to a misjudgment of the real marginal situation, substantially enhancing the fatigue of the components.
ACKNOWLEGDEMENTS
The authors would like to express their gratitude to José Luiz Batista for his help in preparing the test samples. All equipment and materials used in this research were kindly supplied by CONEXÃO and WILCOS Companies. This research was conducted at the Department of Dental Materials and Prosthodontics of UNESP - São Paulo State University "Júlio de Mesquita Filho", São José dos Campos Dental School . Dr. Ivan Balducci performed statistical analyses.
Correspondence to
UNESP - São Paulo State University "Júlio de Mesquita Filho" São José dos Campos Dental School. Department of Dental Materials and Prosthodontics
Eng. Francisco José Longo Av., 777
Jardim São Dimas, São José dos Campos, São Paulo - 12245 000 - Brazil
Phone #: 55-12-39233819 - Fax: 55 12 39479010
E-mail:
diegokv@terra.com.br
Received: May 24, 2004 - Modification: September 28, 2004 - Accepted: October 13, 2004
1- Alkan I, Sertgoz A, Ekici B. Influence of occlusal forces on stress distribution in preloaded dental implant screws. J Prosthet Dent 2004 Apr;91(4):319-25.
Influence of occlusal forces on stress distribution in preloaded dental implant screws
J Prosthet Dent
2004
319
25
4
91
Alkan
I
Sertgoz
A
Ekici
B
2- Anusavice KJ, Carroll JE. Effect of incompatibility stress on the fit of metal ceramic crowns. J Dent Res 1987;66 (8):1341-5.
Effect of incompatibility stress on the fit of metal ceramic crowns
J Dent Res
1987
1341
5
8
66
Anusavice
KJ
Carroll
JE
3- Burguete RL, Johns RB, King T, Patterson EA. Tightening characteristics for screwed joints in osseointegrated dental implants. J Prosthet Dent 1994;71(6):592-9.
Tightening characteristics for screwed joints in osseointegrated dental implants
J Prosthet Dent
1994
592
9
6
71
Burguete
RL
Johns
RB
King
T
Patterson
EA
4- Campbell SD, Pelletier LB. Thermal cycling distortion of metal ceramics: Part I - metal collar width. J Prosthet Dent 1992;67(5):603-8.
Thermal cycling distortion of metal ceramics: Part I - metal collar width
J Prosthet Dent
1992
603
8
5
67
Campbell
SD
Pelletier
LB
5- Carr AB, Gerard DA, Larsen PE. The response of bone in primates around unloaded dental implants supporting prostheses with different levels of fit. J Prosthet Dent 1996;76(5):500-9.
The response of bone in primates around unloaded dental implants supporting prostheses with different levels of fit
J Prosthet Dent
1996
500
9
5
76
Carr
AB
Gerard
DA
Larsen
PE
6- De Hoff PH, Anusavice KJ. Effect of metal design on marginal distortion of metal-ceramic crowns. J Dent Res 1984;63(11):1327-31.
Effect of metal design on marginal distortion of metal-ceramic crowns
J Dent Res
1984
1327
31
11
63
De Hoff
PH
Anusavice
KJ
7- Fonseca JC, Henriques GE, Sobrinho LC, de Goes MF. Stress-relieving and porcelain firing cycle influence on marginal fit of commercially pure titanium and titanium-aluminum-vanadium copings. Dent Mater 2003 Nov;19(7):686-91.
Stress-relieving and porcelain firing cycle influence on marginal fit of commercially pure titanium and titanium-aluminum-vanadium copings
Dent Mater
2003
686
91
7
19
Fonseca
JC
Henriques
GE
Sobrinho
LC
de Goes
MF
8- Goheen KL, Vermilyea SG, Vossoughi J, Agar JR. Torque generated by handheld screwdrivers and mechanical torquing devices for osseointegrated implants. Int J Oral Maxillofac Implants 1994 Mar-Apr;9(2):149-55.
Torque generated by handheld screwdrivers and mechanical torquing devices for osseointegrated implants
Int J Oral Maxillofac Implants
1994
149
55
2
9
Goheen
KL
Vermilyea
SG
Vossoughi
J
Agar
JR
9- Guichet DL, Caputo AA, Choi H, Sorensen JA. Passivity of fit and marginal opening in screw-or cement-retained implant fixed partial denture designs. Int J Oral Maxillofac Implants 2000;15(2):239-46.
Passivity of fit and marginal opening in screw-or cement-retained implant fixed partial denture designs
Int J Oral Maxillofac Implants
2000
239
46
2
15
Guichet
DL
Caputo
AA
Choi
H
Sorensen
JA
10- Hecker DM, Eckert SE. Cyclic loading of implant-supported prostheses: changes in component fit over time. J Prosthet Dent 2003 Apr;89(4):346-51.
Cyclic loading of implant-supported prostheses: changes in component fit over time
J Prosthet Dent
2003
346
51
4
89
Hecker
DM
Eckert
SE
11- Jemt T, Book K. Prosthesis misfit and marginal bone loss in edentulous implant patients. Int J Oral Maxillofac Implants 1996;11(5)620-5.
Prosthesis misfit and marginal bone loss in edentulous implant patients
Int J Oral Maxillofac Implants
1996
620
5
5
11
Jemt
T
Book
K
12- Jemt T, Lekholm U. Measurements of bone and framework deformations induced by misfit of implant superstructures: a pilot study in rabbits. Clin Oral Implants Res 1998;9(4):272-80.
Measurements of bone and framework deformations induced by misfit of implant superstructures: a pilot study in rabbits
Clin Oral Implants Res
1998
272
80
4
9
Jemt
T
Lekholm
U
13
13- Kallus T, Bessing C. Loose gold screws frequently occur in full-arch fixed prostheses supported by osseointegrated implants after 5 years. Int J Oral Maxillofac Implants 1994;9(2):169-78.
14- Keith SE, Miller BH, Woody RD, Higginbottom FL. Marginal discrepancy of screw-retained and cemented metal-ceramic crowns on implants abutments. Int J Oral Maxillofac Implants 1999;14(3):369-78.
Marginal discrepancy of screw-retained and cemented metal-ceramic crowns on implants abutments
Int J Oral Maxillofac Implants
1999
369
78
3
14
Keith
SE
Miller
BH
Woody
RD
Higginbottom
FL
15- Koke U, Wolf A, Lenz P, Gilde H.In vitro investigation of marginal accuracy of implant-supported screw-retained partial dentures. J Oral Rehabil 2004 May;31(5):477-82.
In vitro investigation of marginal accuracy of implant-supported screw-retained partial dentures
J Oral Rehabil
2004
477
82
5
31
Koke
U
Wolf
A
Lenz
P
Gilde
H
16- Michaels GC, Carr AB, Larsen PE. Effect of prosthetic superstructure accuracy on the osseointegrated implant bone interface. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 1997; 83(2):198-205.
Effect of prosthetic superstructure accuracy on the osseointegrated implant bone interface
Oral Surg Oral Med Oral Pathol Oral Radiol Endod
1997
198
205
2
83
Michaels
GC
Carr
AB
Larsen
PE
17
17- Millington ND, Leung T. Inaccurate fit of implant superstructures. Part 1: Stresses generated on the superstructure relative to the size of fit discrepancy. Int J Prosthodont 1995; 8(6):511-6.
18- Rangert B, Jemt T, Jorneus L. Forces and moments on Branemark implants. Int J Oral Maxillofac Implants 1989;4(3):241-7
Forces and moments on Branemark implants
Int J Oral Maxillofac Implants
1989
241
7
3
4
Rangert
B
Jemt
T
Jorneus
L
19- Sahin S, Cehreli M. The significance of passive framework fit in implant prosthodontics: current status. Implant Dent 2001;10(2):85-92.
The significance of passive framework fit in implant prosthodontics: current status
Implant Dent
2001
85
92
2
10
Sahin
S
Cehreli
M
20- Sertgoz A. Finite element analysis study of the effect of superstructure material on stress distribution in an implant-supported fixed prosthesis. Int J Prosthodont 1997;10(1):19-27.
Finite element analysis study of the effect of superstructure material on stress distribution in an implant-supported fixed prosthesis
Int J Prosthodont
1997
19
27
1
10
Sertgoz
A
21- Smedberg JI, Nilner K, Rangert B, Svensson SA, Glantz SA.On the influence of superstructure connection on implant preload: a methodological and clinical study. Clin Oral Implants Res 1996;7(1):55-63.
On the influence of superstructure connection on implant preload: a methodological and clinical study
Clin Oral Implants Res
1996
55
63
1
7
Smedberg
JI
Nilner
K
Rangert
B
Svensson
SA
Glantz
SA
22- Tzenakis GK, Nagy WW, Fournelle RA, Dhuru VB. The effect of repeated torque and salivary contamination on the preload of slotted gold implant prosthetic screws. J Prosthet Dent 2002 Aug;88(2):183-91.
The effect of repeated torque and salivary contamination on the preload of slotted gold implant prosthetic screws
J Prosthet Dent
2002
183
91
2
88
Tzenakis
GK
Nagy
WW
Fournelle
RA
Dhuru
VB
23- Vasconcellos DK, Cardoso AC, Bottino MA, Magini RS, Adriani Jr WA. High temperature dimensional alterations of implant supported frameworks. Braz J Oral Sci 2005 Jan-Mar;4(12):689-94.
High temperature dimensional alterations of implant supported frameworks
Braz J Oral Sci
2005
689
94
12
4
Vasconcellos
DK
Cardoso
AC
Bottino
MA
Magini
RS
WA
Adriani Jr
24- Watanabe F, Uno I, Hata Y, Neuendorff G, Kirsch A. Analysis of stress distribution in a screw-retained implant prosthesis. Int J Oral Maxillofac Implants 2000 Mar-Apr;15(2):209-18.
Analysis of stress distribution in a screw-retained implant prosthesis
Int J Oral Maxillofac Implants
2000
209
18
2
15
Watanabe
F
Uno
I
Hata
Y
Neuendorff
G
Kirsch
A
25- Winkler S, Ring K, Ring JD, Boberick KG. Implant screw mechanics and the settling effect: overview. J Oral Implantol 2003;29(5):242-5.
Implant screw mechanics and the settling effect: overview
J Oral Implantol
2003
242
5
5
29
Winkler
S
Ring
K
Ring
JD
Boberick
KG
26- Wu Y, Moser JB, Jameson LM, Malone WF. The effect of oxidation heat treatment on porcelain bond strength in selected base metal alloys. J Prosthet Dent 1991 Oct;66(4):439-44.
The effect of oxidation heat treatment on porcelain bond strength in selected base metal alloys
J Prosthet Dent
1991
439
44
4
66
Wu
Y
Moser
JB
Jameson
LM
Malone
WF
27- Yanase RT, Binon PP, Jemt T, Gulbransen HJ, Parel S. Current Issues Forum. How do you test a cast framework fit for a full-arch fixed implant-supported prosthesis? Int J Oral Maxillofac Implants 1994;9(4):469-74.
Current Issues Forum. How do you test a cast framework fit for a full-arch fixed implant-supported prosthesis?
Int J Oral Maxillofac Implants
1994
469
74
4
9
Yanase
RT
Binon
PP
Jemt
T
Gulbransen
HJ
Parel
S
28- Zervas PJ, Papazoglou E, Beck FM, Carr AB. Distortion of three-unit implant frameworks during casting, soldering, and simulated porcelain firings. J Prosthodont 1999 Sep;8(3):171-9.
Distortion of three-unit implant frameworks during casting, soldering, and simulated porcelain firings
J Prosthodont
1999
171
9
3
8
Zervas
PJ
Papazoglou
E
Beck
FM
Carr
AB
Autoria
Diego Klee de Vasconcellos
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Marco Antonio Bottino
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Renato Sussumu Nishioka
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Luiz Felipe Valandro
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Elza Maria Valadares da Costa
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
SCIMAGO INSTITUTIONS RANKINGS
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Universidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, BrazilUniversidade Estadual PaulistaBrazilSão Paulo, BrazilUniversidade Estadual Paulista, Department of Dental Materials and Prosthodontics , São José dos Campos Dental School, São Paulo, Brazil
Vasconcellos, Diego Klee de et al. Avaliação do efeito da força de aperto de parafusos de retenção na desadaptação marginal de próteses sobre implantes. Journal of Applied Oral Science [online]. 2005, v. 13, n. 2 [Acessado 4 Abril 2025], pp. 120-125. Disponível em: <https://doi.org/10.1590/S1678-77572005000200005>. Epub 05 Set 2005. ISSN 1678-7765. https://doi.org/10.1590/S1678-77572005000200005.
Faculdade De Odontologia De Bauru - USPServiço de Biblioteca e Documentação FOB-USP, Alameda Dr. Octávio Pinheiro Brisolla 9-75, 17012-901 Bauru SP Brasil, Tel.: +55 14 3235-8373 -
Bauru -
SP -
Brazil E-mail: jaos@usp.br
rss_feed
Acompanhe os números deste periódico no seu leitor de RSS
scite shows how a scientific paper has been cited by providing the context of the citation, a classification describing whether it supports, mentions, or contrasts the cited claim, and a label indicating in which section the citation was made.