ABSTRACT
High-temperature applications like turbine blades and braking discs employ Nimonic 90 superalloy, which is hard and wears electrodes during Electrical Discharge Machining. Under different EDM process conditions (current, duty cycle, pulse duration, and servo voltage), this study examines the wear behavior of square copper electrodes with 0.5, 0.6, 0.7, and 0.8 mm sizes. It focuses on cutting time (CT), electrode radius (ER), electrode wear length (EWL), and electrode taper angle Based on ANOVA, current was most important to ETA, EWL, pulse length to ER, and duty cycle to CT. Current and servo voltage increased ETA and EWL linearly, whereas duty cycle lowered CT. Micro-craters generated on electrode surfaces due to unstable discharges and skin reactions. After 225 µs pulse duration, the electrode radius decreased due to sparking instability. Experiments confirmed that the multi-objective decision-making approach (VIKOR) optimized process parameters, trade-off between ETA and ER maximization and EWL and CT reduction, and improved electrode performance. A new knowledge of micro-scale square electrode wear on Nimonic 90 may be utilized to improve settings and achieve high machining efficiency and electrode life in precision EDM.
Keywords:
Cutting time; EDM; Nimonic 90; taper angle; wear length.
1. INTRODUCTION
EDM is a thermoelectric, nonconventional machining process that discovers application in creating complex geometry in electrically conductive materials those are impractical and has difficulties to machine by other conventional methods. In EDM, material is removed in a sequential pattern of targeted electric discharges among a tool electrode and a specimen that is immersed in a dielectric fluid leading to the localized melting and vaporization of material [1]. Due to its practical feasibility to machine intricate shapes with dimensional accuracy regardless of the hardness of the metal material, EDM is extensively used in aerospace, nuclear, automotive, and tools manufacturing especially with nickel-based superalloys and advanced composites [2].
Nickel-based superalloys are broadly used in high-temperature structural components, including turbine blades, combustion chambers, aerospace fasteners since they have high creep and oxidation stability and mechanical strength at high temperatures compared to other superalloys. But it is the very same properties that severely diminish machinability when machined under conventional conditions, resulting in undue tool life and lacking surface integrity. Consequently, EDM has become one of the machining paths of Nimonic alloys and other superalloys [3, 4]. Even with its benefits, EDM performance is limited by the electrode wear of tools which negatively influences dimensional accuracy, surface quality and process economics.
The electrode wear in EDM is a complicated phenomenon that is controlled by thermal loading, distribution of sparks, properties of electrode materials, dielectric breakdown characteristics, and process parameters including discharge current, duty factor and pulse on-time [5, 6]. Quantitative studies have revealed that the rate of wear of electrodes (EWR) rises with the higher discharge energy whereas pulse off-time has an impact on the evacuation of the debris and the stability of the sparks [7]. Tsai and Masuzawa [8] suggested an electrode wear resistance index, and found that, wear processes in macro-EDM and micro-EDM are significantly different, because energy density is concentrated with the scale. Geometric inaccuracy has been found to be a significant issue with uneven wear distribution especially on the edges and corners of electrodes [9, 10].
Recent research has underlined that electrode geometry and size is determinant in the wear behaviour, machining success and feature precision. Liu et al. [11] established that as the size of the electrode decreases, it escalates the density of sparks leading to localized wear and decreased life cycle of the tool. The use of advanced engineering materials has recently been investigated and the need for a combination of statistical techniques and multi-response optimization methodologies to enhance the machining performance and surface integrity has been underlined. But, relatively less work has been done on geometric degradation of non-cylindrical electrodes [12]. In addition, the numerical and experimental analyses on shape distortion and dimensional deviation of electrodes during EDM have shown that tapers develop and corners are rounded in the course of extended machining [13, 14]. Square electrodes that are typically employed in the creation of profiled cavities and square holes are especially susceptible to non-homogeneous wear because of the concentration of sparks on sharp edges [15, 16]. It has been experimentally established that corner wear and wear length prevail in the reduction of geometric fidelity of square electrodes, with a direct impact on the taper angle and radius change [9].
In order to reduce electrode wear and enhance the machining performance, there has been substantial research at the electrode materials, surface modification as well as the design of the electrode alternative. A comparison of electrodes made of copper, brass, graphite, and copper alloy has found that the copper-based electrodes tend to be more accurate in their dimensions, but they wear out much faster under high-energy environments [17, 18]. Such sophisticated methods as cryogenic treatment, laser hardening, plasma nitriding, and additive manufacturing of electrodes have proven to have quantified decreases in EWR and enhanced wear uniformity [4, 19]. It has been demonstrated in the context of micro-EDM that electrode coating and nickel-plated electrodes can have an effect on the surface morphology and wear resistance [20].
Dielectric composition and flushing plans also affect the electrode wear and geometric stability. Powder mixed EDM and surfactant-based EDM were demonstrated to augment the distribution of sparks, decrease thermal gradients, and avert the surface finishing, although it exhibits complicated impacts on the electrode wear [21, 22]. The focus on renewable and biodegradable dielectrics has been applied to sustainable EDM, with results showing enhanced dimensional accuracy, although effects on tool wear are inconsistent in response to electrode material and polarity [23, 24]. Designs of internal flushing and slotted electrodes have been suggested to enhance the removal of debris and abnormal discharges reduction [25, 26].
Regarding nickel-based superalloys, significant ongoing EDM studies have been done on Inconel 600, 617, 718, and Waspaloy, and surface integrity, MRR, and tool wear analyzed in detail [27, 28]. Vivek et al. [4] expressed enhanced performances of graphite electrode in EDM of Nimonic 90 by means of surface modification, whereas Shastri and Mohanty [3] touched the issue of sustainability in machining Nimonic C263. However, there are very few systematic investigations devoted to the wear of square copper electrodes and geometrical degradation of their shape in EDM of Nimonic 90.
As there are conflicting requirements involved in productivity, dimensional accuracy and life of electrode in EDM performance, the multi-criteria decision-making (MCDM) approaches are now indispensable tools for the optimization of the process. There are different techniques such as Grey Relational Analysis (GRA), TOPSIS, COPRAS and Artificial Intelligence based techniques that have been successfully used in EDM applications [29,30,31,32]. Recently, the GRA and statistical optimization techniques have been proven to be effective in enhancing machining performance and surface characteristics of advanced materials [33]. However, the VIKOR approach has the unique feature that it provides a compromise solution by taking account of the maximum group utility and the minimum individual regret [34, 35]. Thus, VIKOR gives a balance score in ranking the competing alternatives and is especially appropriate for the optimization problems with contradictory response characteristics. Therefore, VIKOR method was used in the present study to maximize the electrode taper angle and the electrode radius and minimize the electrode wear length and cutting time. Nevertheless, the sensitivity of Vikingor based EDM-based studies focuses on surface roughness and MRR with little consideration of electrode geometric wear factors, i.e., taper angle, wear length, and corner radius, particularly of non-cylindrical electrodes.
Based on the above studies, it is evident that though the effects of EDM electrode wear have been widely analyzed, a complete framework on incorporating square copper electrode size effects, geometric wear, cutting time and multi-criteria optimization of EDM of Nimonic 90 does not exist. Reported literature is either on various materials, cylindrical electrodes or individual measures of performance, but not a coordinated effect of electrode geometry and process parameters on dimensional fidelity. Although there are many advances in the EDM research, systematic investigations on the systematic changes of the geometry of square copper micro-electrode during the EDM of Nimonic 90 are still limited. The synergy between the taper angle of the electrode, corner radius of the electrode and wear length of the electrode for various cross sectional sizes of electrodes and multi response optimization by VIKOR approach have not been explored much in the literature. Thus, the present study gives the complete picture of degradation mechanisms of the electrode and optimum machining conditions to improve the dimensional accuracy in EDM of Nimonic 90. Practically, the knowledge of the geometric degradation behaviour of micro-scale square electrodes is crucial to enhance the dimensional accuracy, machining efficiency and electrode life in EDM of nickel based superalloy. These enhancements are especially useful for aerospace and turbine, mould and precision manufacturing applications. Furthermore, the increased efficiency of the process and the decreased consumption of electrodes help to lower manufacturing costs and improve sustainability by more efficiently using materials and energy resources.
2. MATERIALS AND METHODOLOGY
Nimonic 90 is a high-quality nickel-based superalloy that has excellent performance in high temperatures and mechanical strength. The specific composition of Nimonic 90 is presented in Table 1. In aerospace, aviation, nuclear reactor applications, the creation of accurate square holes with insignificant wear of electrodes is of great necessity. Nevertheless, it is extremely difficult to make square holes in Nimonic 90 by standard machining methods, as the tool wears extremely and it is difficult to ensure surface integrity. Square holes were therefore made on Nimonic 90 with the traditional EDM process parameters.
Copper was selected as the electrode material because of its high electrical conductivity, good thermal conductivity, high dimensional stability and its application in precision EDM process. These features help to make the spark stable and heat dissipates efficiently to allow better dimensional accuracy and less machining instability. Also, a set of square electrodes of different sizes (0.5–0.8 mm) were selected to systematically study the effect of micro-scale geometric changes on the degradation behaviour of the electrodes during the EDM of Nimonic 90. The size range selected is a range of practical sizes that are likely to be found in precision machining applications and offers a good compromise between stiffness and wear sensitivity.
The EDM process parameters were varied systematically with the electrode size to obtain maximum ER and ETA and reduced CT and EWL. Before the experiments, pilot machining trials were carried out to set the stable discharge condition to make square cavities. Currents less than 3A yielded too little spark energy, and led to a circular hole geometry rather than the desired square geometry. Hence 3 A was chosen as the minimum current and 12 A as the maximum current to prevent over heating of the electrodes and to prevent excessive electrode wear. The duty cycle, pulse duration and servo voltage ranges were selected to ensure stable inter electrode conditions, and to allow systematic assessment of the geometric degradation characteristics [36, 37] and as summarized in Table 2.
As far as the results stated in [36] suggest, the values of duty cycle (DC) were differentiated (ranged between 30–70 percent). On this basis, the current research extended the DC range between 20% up to 80% with constant intervals of 20%. In line with this, off-time values of pulse were taken to be 300 µs (20% DC), 225 µs (40% DC), 150 µs (60% DC), and 75 µs (80% DC). Experiments were carried out based on the chosen levels of duty cycles. The pressure of EDM oil flushing was kept at 0.6 kg/cm2 at all times during the experiment runs.
Based on the design of the experiment, Nimonic 90 specimens of 1.5 mm thickness were machined using square copper electrodes of side length 0.5, 0.6, 0.7 and 0.8 mm. Figure 1 shows the EDM experimental set-up. The main input parameters were chosen as discharge current (A), servo voltage (V), duty cycle (percentage), and pulse duration (µs). The electrodes were made out of copper and a vertical machining centre was used to produce them with an optical microscopic image of a representative square electrode being Figure 2.
EWL, ER and ETA were assessed using a video measuring apparatus and a scanning electron microscope (SEM). The time taken was measured with a stopwatch. Figure 3 shows the schematic drawing of the electrode’s taper angle, radius, lengths of worn electrode and machined electrode and length of central axis.
2.1. Visekriterijumsko kompromisno rangiranje method (VIKOR)
VIKOR is a multi-criteria optimization and compromise solution for improving the decision-making quality based on the ranking procedure [34]. This method is already used in concrete structure repair, performance evaluation, biomedical, and selection of materials. The following information is essential to study for applying the VIKOR method. There are two criteria assigned to problems such as beneficial criteria and non-beneficial criteria. In this work, beneficial criteria are considered to have a higher value desired, such as the ETA and ER (maximization), whereas non-beneficial criteria are considered to have a lower value desired, such as the EWL and CT (minimization). The weights are normally assigned to every criterion (performance measures) based on the customer need/industrial demand. The steps are given below.
Step 1: Assign the weights to beneficial criteria and non-beneficial criteria.
The 0.25 weightage is assigned to both beneficial criteria and non-beneficial criteria.
Step 2: Find: (a) (best) and (worst) value for criteria.
Assuming, each alternative is calculated as per each criterion objective, the compromise ranking is calculated by comparing the closeness measure to the ideal alternative. The m alternatives are considered as A1, A2, … , Am. The fij is the value of the jth criterion for the alternative Ai.
The (best) and (worst) are the maximum and minimum values from the responses, respectively, and calculated for each response.
(b) Formulate ranking measure values Si and Ri; i = 1, 2, …, m,
Here, Si, wj, and Ri are considered as unity measures, the weight of criteria and individual regret, respectively.
Step 3: Compute Qi
Here, the weight of strategy is 0.5 ʋ.
Step 4: Ranked the alternatives and sorted (Descending order) by S, R, and Q values.
Step 5: Best alternatives are calculated with minimal Q with satisfied C1 and C2 conditions.
C1: Acceptable advantage
The A″ is denoted as the second alternative rank whereas A′ is denoted as the first alternative rank.
C2: Acceptable stability in decision-making.
The alternative A′ is must be the best ranked by S or/and R. Even though one condition is not satisfied, a set of compromise solutions are proposed.
If the C1 condition is not satisfied, find the AM
If the C2 condition is not satisfied, select the alternatives A′ and A″.
To minimize the variability of the measurement, all the measurements were carried out under the same machining conditions on calibrated video measuring equipment and SEM. The number of experimental observations was then tested statistically to see if they were sufficient. The relatively high value of the coefficient of determination for the three factors (electrode taper angle, electrode wear length and cutting time) suggest that the experimental observations and the model predictions are in good agreement and so the measured responses are reliable.
3. RESULTS AND DISCUSSIONS
The machining of square holes on Nimonic 90 was done according to the design of the experiment. After machining, square copper electrodes of size 0.5, 0.6, 0.7 and 0.8 mm were measured in terms of novel response parameters, which were electrode wear length electrode taper angle, and electrode radius. Besides this, the time that each experimental run took to cut was also noted. Tables 3 and 4 contain the layout of the experimental design and the values of the responses respectively.
The mean values of each response were obtained at various levels of parameters. The maximum and minimum mean values were calculated in response to each response variable and the delta value was obtained by taking the difference between the maximum and the minimum mean values. The processes parameter was ranked according to the delta values with the one that had the largest delta value being ranked the first and regarded as the most important.
A comparative analysis was conducted among the most important process parameters in relation to EWL, ER, ETA and CT to assess the overall EDM performance.
3.1. Electrode taper angle
The angle between the central axis of the electrode and the sloping surface of the worn-out electrode is termed as the ETA as seen in the schematic drawing (Figure 3) where the angle is represented by the dotted blue line. The maximum ETA is a desirable state as the higher ETA, the lower is the electrode wear. In all experimental circumstances, the worn-out surface areas and edges of the electrodes formed tapers and this agrees with the findings in the literature [9].
According to Figure 4(a) discharge current is observed as the most influential process parameter in case of square electrodes of 0.5, 0.6, 0.7, and 0.8 mm dimensions. This is because thermal energy is known to be involved in the concurrent excision of the work piece and the electrode material. The higher the discharge current, the more the thermal energy created, which causes increased wear on the electrode surfaces and edges. Moreover, copper electrodes can take off more workpiece material because they are highly thermally conductive and have good heat dissipation capacity leading to higher metal removal. The thermal conductivity of copper is directly proportional to the rate of removal of the metal due to increased heat dissipation as stated in [14].
Figure 5(a) showed that the enhancement percentage of ETA of the square electrodes of 0.5, 0.6, 0.7 and 0.8 mm improved with increase in the most important process parameter. Values of ETA raised gradually with the increase in discharge current of the 0.5 to 0.8 mm square electrode. The reasons behind this trend can be elucidated by the summation of the electrode area, skin effect, and uneven distribution of sparks between the work piece material and the square electrode. As the discharge current increased, the ETA also improved in a quantitative manner by 40.313% with values of 2.316° to 1.383°; by 50.620% with values of 2.912° to 1.438°; by 58.335% with values of 3.727° to 2.174°; and by 63.180% with values of 4.808° to 1.770°.
The electrode taper angle was maximum at 0.8 mm square electrode when a 12 A discharge current was used. The objective of using maximum electrode taper angle is explained by the fact that it is associated with minimum electrode wear as compared to the ideal square geometry of electrode. Contrastingly, the electrode taper angle was the lowest with the 0.5 mm square electrode with a discharge current of 3 A.
These results are in agreement with the findings in the study [13] where the minimum electrode taper angle was 14° at a discharge current of 27.4 A during EDM of a copper electrode. According to this comparison, the current findings are in good agreement especially the behaviour of the electrode taper angle at a discharge current of 3 A.
3.2. Electrode radius
In each experimental run with different process parameters, the square electrode acquired a conical shape at the end. This conical geometry is largely because of short-circuit development in a high-level manner especially in machining of micro features and skin effects of square electrode geometry. Diffusion of heat in corners of square electrodes is strongly associated to diffusion of heat in corners, and the rounded corner is aggravated by the large thermal conductivity of the electrode material [8].
The experimental findings show that the ER at the electrode end is greatly affected by the parameters of the EDM processes and square electrode size, 0.5, 0.6, 0.7 and 0.8 mm. The respective results are represented in Figure 4(b). Electrode radius analysis showed that pulse duration is the most critical parameter influencing ER of all square electrode sizes as is also demonstrated by Figure 5(b).
With square electrode of 0.5, 0.6, 0.7 and 0.8 mm, there was an increase in electrode radius with pulse duration to a point of 225 µs and a decrease in electrode radius beyond 225 µs. Increase in pulse duration causes increase in electrode radius at shorter pulse durations but as pulse duration increases further the electrode radius reduces continuously. This is caused by the over-effects of excessive chopping in machining zone which facilitates short circuiting between the electrode and the work material thus decreasing the EDM performance [30]. Thus, ER rises within the first pulse duration range and falls with further pulse duration increments.
The electrode radius improved by 34.48, 34.94, and 34.22% with the increase of the pulse duration with the 0.5, 0.6, and the 0.7 mm square electrode, respectively; and the range of values increased by 0.259 to 0.169 mm, 0.346 to 0.225 mm, and 0.435 to 0.286 mm, correspondingly.
Of all the electrode sizes, the 0.8 mm square electrode had the highest electrode radius in case 300 µs pulse was used. The current results are superior to those that had been previously reported in the study of the electrode radius [13], where the electrode radius rose between 0.773 mm and 0.702 mm with the change in discharge current between 27.4A and 33.4A.
3.3. Electrode wear length
EWL can be determined by the difference between the length of fresh electrode and the length of worn-out electrode at the end of machining. The schematic diagram of the fresh, partially worn-out electrodes and fully worn-out electrodes with the corresponding EWL is presented in Figure 6. In the case of square electrode, the calculation of EWL takes place in the y direction with the cross-section of the electrode along the x-direction and the length of the electrode along the y-direction. After the machining, wear of the electrodes was noted both in the x- and y- directions. Nevertheless, the y-direction electrode wear was higher as compared to the wear on the x-direction electrode cross-section. This is explained by the comparatively slow process of EDM, which causes a higher contact of machining in the y-direction, and by the scarcity of heat transfer in machining [5].
Schematic diagram for EWL in cross-section (x-direction): length (y-direction). (a) Fresh, (b) partially worn-out, and (c) fully worn-out electrode.
Electrode wear length analysis revealed that discharge current was the most important parameter that affected EWL in square electrodes (0.5, 0.6, 0.7 and 0.8 mm) as depicted in Figure 4(c). The effect of square electrode size and discharge current on EWL was also investigated jointly and it is depicted in Figure 5(c). Generally, the area effect yields smaller electrode wear lengths, when compared to smaller electrode wear lengths, in larger electrode sizes [11].
The EWLs of square electrodes of 0.5, 0.6, 0.7 and 0.8 mm rose with the rise in the discharge current, as more unstable sparks were formed between the square electrode and the work material. On the other hand, considering the electrode of 0.8 mm square, the change of EWL with increasing current was marginally enhanced and this is owed to the combined effect of the skin and the area effects. The EWL were amplified by 19.88, 18.32, 15.95, and 7.85 percent with the growing discharge current on the square electrodes of 0.5, 0.6, 0.7 and 0.8 mm, respectively.
It was therefore seen that the square electrode size of 0.8 mm had the shortest length of electrode wear in working conditions at a discharge current of 3 A as stated in [38].
From an industrial point of view, the taper angle of the electrode and the length of the electrode wear are important parameters to control the dimensional accuracy, corner integrity and electrode life in precision EDM process. Too much taper formation results in a deviation from the desired geometry, and impacts the dimensional fidelity of square holes and profiled cavities. Likewise, the length of the electrodes decreases as the electrodes wear, causing a variation in spark gap conditions, and requiring frequent electrode replacement. Therefore, the higher the amount of wear, the higher the machining costs and the lower the productivity of the machining process. Hence, it is important to minimize the degradation of the geometry of the electrode to ensure process stability and a high level of accuracy in the aerospace, turbine, mould and high value manufacturing applications. The same practical aspects have been emphasized in recent research on high precision EDM processes with advanced materials [39].
3.4. Cutting time
CT was the time taken in cutting a square hole on the work piece. The effect of the duty cycle and square electrode size of 0.5, 0.6, 0.7 and 0.8 mm on CT was investigated and the respective findings are shown in Figure 4(d). Duty cycle was found to be the most important parameter influencing cutting time of all sizes of square electrode. The percentage of CT enhancement with regard to duty cycle against various square electrode sizes was computed and shown in Figure 5(d).
In square electrodes with 0.5, 0.6, 0.7 and 0.8 mm cutting time and an increase in duty cycle declined in a consistent manner. This is because the direct relationship exists between duty cycle and pulse duration [40]. Pulse duration on the other hand controls the rate at which both the work piece and the electrode are removed. Consequently, a rise in duty cycle will increase the efficiency of material removal and hence less cutting time. Also, the area effect and skin effect of square electrodes contributes to the decrease in CT. The same tendencies have been observed in earlier researches [15].
In addition, it was found that the cutting time decreased with the increase in the size of the electrode (0.5 mm to 0.8 mm) due to the contact area effect. Specifically, a square electrode of 0.8 mm had lower cutting time than the electrode of 0.5 mm. Quantitatively, the cutting time was improved by 79.2% with the 0.5 mm, 83.6% with the 0.6 mm, 77.1% with the 0.7 mm, and 78.2% with the 0.8 mm square electrode with the increase in the duty cycle. When using a duty cycle of 80, the 0.6 mm square electrode had the lowest cutting time of all the tested conditions.
3.5. Analysis of variance
Analysis of variance (ANOVA) was used to determine the contribution of the discharge current (I), pulse duration (Ton), duty cycle (DC) and servo voltage (SV) to the response characteristics (electrode taper angle (ETA), electrode radius (ER), electrode wear length (EWL) and cutting time (CT)) [41]. The statistical analysis was carried out using MINITAB software and the results in terms of the contribution percentages are presented in Table 5.
Discharge current had the highest contribution percentage for all the electrode sizes in ETA, which was increased gradually from 33.46% (0.5 mm electrode) to 65.16% (0.8 mm electrode). The increase in discharge current leads to greater discharge energy that is transferred to the machining area, which results in the preferential melting and erosion at the electrode tip and edges, as indicated by this behaviour. As a result, the greater the thermal loading, the greater the deviation of the geometry of the square electrode and the faster the taper is formed. Recent EDM studies have indicated similar trends with the discharge energy being the most important factor in determining the geometric degradation and tool wear [42, 43].
When it comes to electrode radius, the pulse duration was determined to be the most important parameter and accounted for about 38–39% regardless of the electrode size. At first, the longer pulse duration will help to ensure the stability of spark generation and controlled material removal, hence a larger corner radius. But, very long pulses result in unstable plasma channels, debris accumulation and secondary discharge phenomena, which results in irregular erosion and variation in radius measurements. Thus ER was statistically less significant as indicated by the lesser values of coefficient of determination and adjusted coefficient of determination. The same has been noted in recent EDM investigations, where the scatter of experimental data of the geometric parameters of corner wear was found to be larger than the conventional machining responses due to the local discharge instability and non-uniform debris distribution.
Again, for EWL, discharge current was found to be the most important factor ranging between 39.73% and 85.09% depending on the size of the electrodes. As the current is increased, the plasma channel temperature, and the current density, also increases, resulting in a greater melting and vaporization of the electrode material. Longitudinal wear is present throughout the machining cycle, therefore, higher discharge energy will lead to more material removal in the axial direction and thus increase the length of wear of the electrode. Experimental error values were relatively small (<5%) which show good agreement between the experimental observations and the trend predicted by the models and thus the reliability of the developed models.
Regarding cutting time, duty cycle had the highest contribution percentages of 41.23% to 71.21%. An increase in the duty cycle leads to longer actual sparks and higher discharge frequency, which leads to higher material removal rate and shorter machining time. The R2 and adjusted R2 values are relatively high which indicates that the models developed are good and can be used for prediction purposes.
The overall conclusions of the ANOVA results are that the geometric degradation characteristics are mainly influenced by the discharge current while the machining productivity is mainly influenced by the duty cycle. Although the statistical significance of the response is lower in comparison to ER, it is still an important indicator of corner integrity and dimensional fidelity [26]. Hence, all the responses were taken into account in the following optimization process to get a balance compromise solution. The results are in line with recent investigations on EDM which have shown the need to take into account several characteristics of the response to evaluate and optimize the process.
3.6. Electrode surface analysis
Figure 7 shows the surface morphology of the square copper electrodes after machining under the optimum operating conditions under the conditions of wear. The initial square-shaped profiles of the electrodes changed to conical shapes after machining, irrespective of their size, suggesting high geometric degradation as a result of repeated spark discharges. The amount of deformation was found to be higher with higher discharge energy, which shows the high influence of thermal loading on the electrode’s wear characteristic.
Front view of Worn-out electrodes on optimum parameter settings (a) 0.5 mm, (b) 0.6 mm, (c) 0.7 mm, and (d) 0.8 mm.
The gradual change of the geometry from square to conical shape is due to the non-uniform spark energy distribution at the edges and corners of the electrodes. The concentration of edges and the current density in a particular region creates higher temperature which leads to preferential melting and erosion near the electrode extremities. The original sharp corners will thus over time become rounded, causing the formation of tapers and dimensional deviations. The shape evolution phenomenon is reported for the first time in this micro-EDM investigation, but similar phenomenon has been reported in previous investigations with copper electrodes.
It was found that the surfaces of the electrodes were worn and contained many micro-craters, resolidified droplets and debris particles that were adhered to the surface. Such features are typical of a multiple melt and rapid solidification that are associated with the discharge process. The high-temperature plasma channel formed between the electrode and the workpiece results in the local vaporization of the material, and the subsequent high-speed quenching in the dielectric medium. Therefore, the resolidified material is deposited on the electrode surface as spherical droplets and irregular deposits.
The attachment of significant debris on the machined electrode surfaces was also noticed along with the formation of the crater. The debris particles inside the inter-electrode gap tend to cause secondary discharge phenomena and unstable spark generation, which results in local overheating and the geometric deterioration of the electrodes. These secondary discharges add irregular erosion patterns and help to explain the variation in the measurements of the radius of the electrodes. Recent studies have also shown that the plasma instability caused by debris is one of the important factors to determine the morphology and dimensional accuracy of the electrode [13].
In addition, the presence of micro-craters and resolidified layers suggests that the thermal wear mechanisms are the dominant wear mechanisms in the EDM of Nimonic 90. Increased discharge current and pulse duration will increase localized melting and increase the density of craters and roughness of the surface [44]. The results of these observations show that the wear process is mainly controlled by the repeated melting-vaporization cycles and not by the mechanical interaction between the electrode and the workpiece.
The diameters of cones after the machining were about 0.190, 0.299, 0.579 and 0.639 mm for the square electrodes of 0.5, 0.6, 0.7 and 0.8 mm respectively. The conical diameter is seen to increase with the size of the electrode, showing that the larger electrodes have a more rounded edge due to greater exposed surface area and diffusion of heat. The morphology of the craters, the deposition of the debris and the geometric changes observed are consistent with the recent EDM investigations, which indicate that the more energy that is released from the discharge, the more localized melting, rapid solidification and secondary discharge phenomena occur, which increases the rate of electrode degradation.
3.7. Optimum analysis
VIKOR was chosen, due to the fact that it considers both the maximum group utility and minimum individual regret, which helps to balance the ranking of competing alternatives. Each of the four responses was given an equal weight factor of 0.25 to make sure that the four responses were given equal consideration in the geometric accuracy, electrode life, and machining productivity [35]. VIKOR can simultaneously consider multiple performance characteristics and hence, can better reflect the actual machining needs as compared to single-response optimization approaches.
The first step is to find the beneficial and non-beneficial criteria. The ETA and ER are selected as beneficial criteria (maximization) whereas EWL and CT are selected as non-beneficial criteria (minimization). The best and worst values are identified for beneficial criteria and non-beneficial criteria and it is calculated by using equation 1. The unity measure, Si is calculated by using equation 2. The individual regret, Ri is calculated by using equation 3 which is selected based on the maximum value of each alternative. The S*, R*, S-, and R- are calculated by using equations 4 and 5. The S* and R* are the best values of Si and Ri whereas S- and R- are the worst values of Si and Ri respectively. The Qi is calculated by using equation 6. The rank is generated according to minimum Si, Ri and Qi that are displayed as optimum values. According to the experimental outcomes of 0.5 and 0.8 mm square hole, VIKOR method calculations of 0.5 and 0.8 mm square electrodes are done and it is tabulated in Tables 6 and 7 respectively.
The third experimental condition was determined as the most favourable alternative for both square electrodes (0.5 mm and 0.8 mm) since it had the smallest Si, Ri and Qi values. Further confirmation of the robustness of the compromise solution was obtained by satisfying the acceptable advantage and acceptable stability criteria. These results show that the chosen parameter combination is effective to achieve a good dimensional accuracy and machining efficiency.
The confirmation experiments were performed at the optimum conditions and significant improvements were obtained in all the response characteristics as compared to the initial experiments which are shown in Table 8. The higher electrode taper angle and radius are indicative of better dimensional fidelity while the shorter electrode wear length is indicative of a longer electrode life. At the same time, the time saved in cutting verifies improvement in the productivity of the machining. These improvements prove the effectiveness and reliability of the VIKOR methodology to find the favourable process conditions.
The radius of the electrode was also statistically less significant as compared to other parameters, however, the results obtained in the optimization process were not affected by this parameter. The VIKOR approach combines all the response characteristics at once; so the ranking is based on the overall response behaviour instead of on one particular response parameter. Thus, the compromise solution is still valid and has a real significance.
The trends found in the present investigation are broadly similar to the recent EDM optimization studies reported in the literature which have indicated the significance of the proper selection of parameters to control the wear related phenomena and enhance the machining performance [45, 46]. In the present work, similar observations were obtained and it was found that the discharge current was the most important factor to control the electrode taper angle and electrode wear length. The results also further validate the need of systematic parameter optimization for improving the machining performance and dimensional accuracy.
4. CONCLUSIONs
In EDM of Nimonic 90 superalloy, the present study researched the wear properties of square copper electrodes of 0.5, 0.6, 0.7 and 0.8 mm. Under different process parameters, such as duty cycle, pulse duration, current, and servo voltage, key performance measures (EWL, ER, ETA, and CT) were measured.
-
The results have shown that current is the most important parameter that affects the angle of taper of the electrode as well as the length of electrode wear, as the larger currents, the greater the ETA and EWL because of the high thermal energy and erratic sparking. The electrode radius is mainly influenced by pulse duration and peaks at 225 us and thereafter, it goes down, due to the instability of the sparking and short-circuiting effects. Duty cycle was found to be the most common parameter that affects cutting time whereby a high duty cycle was found to have a decreasing effect on cutting time by increasing the rate of metal removal as a result of the extension of the pulse duration.
-
The surface examination with the microscope revealed that the sharp edges of the square electrodes become conical in the end of the electrodes because of unstable discharges and electromagnetic skin effects, which cause the formation of micro-craters and gluing of debris. This morphological transformation increased with the current and pulse duration.
-
The EDM process parameters were effectively optimized using the VIKOR multi-criteria decision-making approach with all the criteria having equal weight, which was maximizing ETA and ER and minimizing EWL and CT. The conditions which VIKOR identified as optimum were experimentally tested and there was a significant improvement in all the response variables relative to the original experimental data.
-
Finally, the study gives new information on wear behaviour and performance optimization of micro-scale square copper electrodes in EDM of Nimonic 90, showing the important role of current, pulse duration and duty cycle. The geometry and surface conditions transformation of electrodes under the different parameters illustrates the need to pay close attention to the process. The VIKOR method is an important tool in terms of balance between various performance criteria, which increases machining efficiency and the life of electrodes in precision EDM applications.
5. LIMITATIONS
While the current research has offered a detailed knowledge of the geometric degradation behaviour of square copper electrodes in EDM of Nimonic 90, some limitations are worth noting. Only Nimonic 90 was studied and the size of the copper electrodes was limited to 0.5 to 0.8 mm. Moreover, formal uncertainty analysis, repeated experiments and comparative evaluation of the different multi-criteria optimization techniques were not the scope of the present work. Thus the optimum conditions reported here should only be regarded as applicable to the system investigated.
6. FUTURE SCOPE
Potential areas for further research could include the application of the current approach to other nickel-based superalloys and other types of electrodes. Furthermore, comparative studies with various multi-response optimization techniques, uncertainty quantification, repeated experiments, and hybrid optimization techniques using artificial intelligence can be conducted to gain more insight into the performance of EDM. Real time monitoring of plasma behaviour and thermal characteristics may also help to understand the geometric wear mechanisms and help to develop intelligent EDM systems for precision manufacturing applications.
7. ETHICAL CONSIDERATIONS
The authors declare that the manuscript does not report any studies involving human or animal participants.
8. ACKNOWLEDGMENTS
The authors declare that no financial support was received from any organization for the work submitted.
9. DATA AVAILABILITY
The data that support the findings of a study are available from the corresponding author upon reasonable request.
10. BIBLIOGRAPHY
-
[1] DAVIM, J.P., Nonconventional Machining, Berlin, De Gruyter, 2022. doi: https://doi.org/10.1515/9783110584479.
» https://doi.org/10.1515/9783110584479 -
[2] ALRUBAYE, I.D.K., FANTONI, G., “Toward green electrical discharge machining (EDM): state of art and outlook”, Machining Science and Technology, v. 27, n. 1, pp. 63–105, 2023. doi: https://doi.org/10.1080/10910344.2023.2194961.
» https://doi.org/10.1080/10910344.2023.2194961 -
[3] SHASTRI, R.K., MOHANTY, C.P., “Sustainable electrical discharge machining of nimonic C263 superalloy”, Arabian Journal for Science and Engineering, v. 46, n. 8, pp. 7273–7293, 2021. doi: https://doi.org/10.1007/s13369-020-05211-0.
» https://doi.org/10.1007/s13369-020-05211-0 -
[4] VIVEK, J., KUMAR, P.V.A., LEWISE, K.A.S., et al., “Improvement in the graphite electrode wear characteristic of electrical discharge machined Nimonic 90 through plasma nitriding, laser hardening and duplex process”, Sadhana, v. 47, n. 4, pp. 186, 2022. doi: https://doi.org/10.1007/s12046-022-01966-4.
» https://doi.org/10.1007/s12046-022-01966-4 -
[5] KHAN, A.A., “Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes”, International Journal of Advanced Manufacturing Technology, v. 39, n. 5-6, pp. 482–487, 2008. doi: https://doi.org/10.1007/s00170-007-1241-3.
» https://doi.org/10.1007/s00170-007-1241-3 -
[6] GHAZI, S., “Investigation the electrode wear rate and metal removal rate in edm process using taguchi and anova method”, Engineering and Technology Journal, v. 38, n. 10A, pp. 1504–1510, 2020. doi: https://doi.org/10.30684/etj.v38i10A.1231.
» https://doi.org/10.30684/etj.v38i10A.1231 -
[7] SRIVASTAVA, V., PANDEY, P.M., “Performance evaluation of Electrical Discharge Machining (EDM) process using cryogenically cooled electrode”, Materials and Manufacturing Processes, v. 27, n. 6, pp. 683–688, 2012. doi: https://doi.org/10.1080/10426914.2011.602790.
» https://doi.org/10.1080/10426914.2011.602790 -
[8] TSAI, Y.Y., MASUZAWA, T., “An index to evaluate the wear resistance of the electrode in micro-EDM”, Journal of Materials Processing Technology, v. 149, n. 1–3, pp. 304–309, 2004. doi: https://doi.org/10.1016/j.jmatprotec.2004.02.043.
» https://doi.org/10.1016/j.jmatprotec.2004.02.043 -
[9] MOURALOVA, K., BEDNAR, J., BENES, L., et al., “The analysis of EDM electrodes wear in corners and edges”, Archives of Civil and Mechanical Engineering, v. 20, n. 4, pp. 1–14, 2020. doi: https://doi.org/10.1007/s43452-020-00137-8.
» https://doi.org/10.1007/s43452-020-00137-8 -
[10] ZOU, Z., ZHANG, X., CHAN, K., et al., “An analysis of the uneven tool electrode wear mechanism in the micro-electrical discharge machining process”, International Journal of Precision Engineering and Manufacturing. Green Engineering, v. 10, n. 6, pp. 1375–1391, 2023. doi: https://doi.org/10.1007/s40684-022-00499-9.
» https://doi.org/10.1007/s40684-022-00499-9 -
[11] LIU, Q., ZHANG, Q., ZHU, G., et al., “Effect of electrode size on the performances of Micro EDM”, Materials and Manufacturing Processes, v. 31, n. 4, pp. 391–396, 2016. doi: https://doi.org/10.1080/10426914.2015.1059448.
» https://doi.org/10.1080/10426914.2015.1059448 -
[12] SELVARAJAN, L., MURUGESAN, C.K., KUMAR, S.S., et al., “Comparative analysis of WCu, WC, and BeCu electrodes using taguchi L18 design for high-performance EDM of additively manufactured AlSi10Mg lattice structures”, Journal of Materials Engineering and Performance, v. 2026, pp. 1–17, 2026. doi: https://doi.org/10.1007/s11665-026-13866-3.
» https://doi.org/10.1007/s11665-026-13866-3 -
[13] LI, X., WANG, Y., LIU, Y., et al., “Research on shape changes in cylinder electrodes incident to micro-EDM”, Advances in Materials Science and Engineering, v. 2019, pp. 8087462, 2019. doi: https://doi.org/10.1155/2019/8087462.
» https://doi.org/10.1155/2019/8087462 -
[14] ZHANG, S., ZHANG, W., WANG, P., et al., “Simulation of material removal process in EDM with composite tools”, Advances in Materials Science and Engineering, v. 2019, pp. 1321780, 2019. doi: https://doi.org/10.1155/2019/1321780.
» https://doi.org/10.1155/2019/1321780 -
[15] HEMA, P., NAVEENA, P., ARUNA, K., “Machining of square holes by using Die-Sinking EDM and optimization of the process parameters”, Materials Today: Proceedings, v. 22, pp. 2751–2763, 2020. doi: https://doi.org/10.1016/j.matpr.2020.03.406.
» https://doi.org/10.1016/j.matpr.2020.03.406 -
[16] RAFAQAT, M., MUFTI, N.A., SALEEM, M.Q., et al., “Enhancing electric discharge machining performance by selecting electrode design and geometrical parameters for square, triangular, and hexagonal profiled holes”, Processes (Basel, Switzerland), v. 11, n. 9, pp. 1, 2023. doi: https://doi.org/10.3390/pr11092661.
» https://doi.org/10.3390/pr11092661 -
[17] ŞIMŞEK, Ü., ÇOĞUN, C., ESEN, Z., “Effects of electrolytic copper and copper alloy electrodes on machining performance in electrical discharge machining (EDM)”, Machining Science and Technology, v. 26, n. 2, pp. 229-244, 2022. doi: https://doi.org/10.1080/10910344.2022.2044855.
» https://doi.org/10.1080/10910344.2022.2044855 -
[18] BHAUMIK, M., MAITY, K., “Effect of different tool materials during EDM performance of titanium grade 6 alloy”, Engineering Science and Technology, an International Journal, v. 21, n. 3, pp. 507–516, 2018. doi: https://doi.org/10.1016/j.jestch.2018.04.018.
» https://doi.org/10.1016/j.jestch.2018.04.018 -
[19] SAHU, A.K., MAHAPATRA, S.S., “Performance analysis of EDM electrode manufactured by direct metal laser sintering during machining of titanium alloy (Ti6Al4V)”, Machining Science and Technology, v. 26, n. 5, pp. 858–893, 2022. doi: https://doi.org/10.1080/10910344.2023.2180750.
» https://doi.org/10.1080/10910344.2023.2180750 -
[20] SIVA, M., ARUNKUMAR, N., SUBRAMANIAN, M., et al., “Influence of micro-electrical discharge machining parameters on the surface morphology of the nickel-coated electrode”, Materials and Manufacturing Processes, v. 38, n. 1, pp. 89–104, 2023. doi: https://doi.org/10.1080/10426914.2022.2105869.
» https://doi.org/10.1080/10426914.2022.2105869 -
[21] ASHOK, M., NIRANJAN, T., CHOKALINGAM, S., et al., “Investigation of powder mixed electrical discharge machining and process parameters optimization using Taguchi based overall evaluation criteria”, IOP Conference Series. Materials Science and Engineering, v. 1057, n. 1, pp. 012075, 2021. doi: https://doi.org/10.1088/1757-899X/1057/1/012075.
» https://doi.org/10.1088/1757-899X/1057/1/012075 -
[22] ISHFAQ, K., SANA, M., WASEEM, M.U., et al., “Surface quality investigation in surfactant-based EDM of Inconel 617 using deep cryogenically treated electrodes”, International Journal of Advanced Manufacturing Technology, v. 127, n. 1-2, pp. 861–878, 2023. doi: https://doi.org/10.1007/s00170-023-11588-7.
» https://doi.org/10.1007/s00170-023-11588-7 -
[23] ISHFAQ, K., SANA, M., REHMAN, M., et al., “Role of biodegradable dielectrics toward tool wear and dimensional accuracy in Cu-mixed die sinking EDM of Inconel 600 for sustainable machining”, Journal of the Brazilian Society of Mechanical Sciences and Engineering, v. 45, n. 4, pp. 1-22, 2023. doi: https://doi.org/10.1007/s40430-023-04126-9.
» https://doi.org/10.1007/s40430-023-04126-9 -
[24] MING, W., XIE, Z., CAO, C., et al., “Research on EDM performance of renewable dielectrics under different electrodes for machining SKD11”, Crystals, v. 12, n. 2, pp. 291, 2022. doi: https://doi.org/10.3390/cryst12020291.
» https://doi.org/10.3390/cryst12020291 -
[25] GAO, M., LIU, M., HAN, J., et al., “Investigation of machining characteristics in electrical discharge machining using a slotted electrode with internal flushing”, Micromachines, v. 14, n. 11, pp. 1, 2023. doi: https://doi.org/10.3390/mi14111989. PMid:38004847.
» https://doi.org/10.3390/mi14111989 -
[26] MURRAY, J., ZDEBSKI, D., CLARE, A.T., “Workpiece debris deposition on tool electrodes and secondary discharge phenomena in micro-EDM”, Journal of Materials Processing Technology, v. 212, n. 7, pp. 1537–1547, 2012. doi: https://doi.org/10.1016/j.jmatprotec.2012.02.019.
» https://doi.org/10.1016/j.jmatprotec.2012.02.019 -
[27] AHMED, A., TANJILUL, M., RAHMAN, M., et al., “Ultrafast drilling of Inconel 718 using hybrid EDM with different electrode materials”, International Journal of Advanced Manufacturing Technology, v. 106, n. 5-6, pp. 2281–2294, 2020. doi: https://doi.org/10.1007/s00170-019-04769-w.
» https://doi.org/10.1007/s00170-019-04769-w -
[28] HARANE, P.P., WOJCIECHOWSKI, S., UNUNE, D.R., “Investigating the effect of different tool electrodes in electric discharge drilling of Waspaloy on process responses.”, Journal of Materials Research and Technology, v. 20, pp. 2542–2557, 2022. doi: https://doi.org/10.1016/j.jmrt.2022.08.015.
» https://doi.org/10.1016/j.jmrt.2022.08.015 -
[29] PASWAN, K., PRAMANIK, A., CHATTOPADHYAYA, S., et al., “An analysis of machining response parameters, crystalline structures, and surface topography during EDM of Die-Steel Using EDM oil and liquid-based viscous dielectrics: a comparative analysis of machining performance”, Arabian Journal for Science and Engineering, v. 48, n. 9, pp. 11941–11957, 2023. doi: https://doi.org/10.1007/s13369-023-07626-x.
» https://doi.org/10.1007/s13369-023-07626-x -
[30] ABHILASH, P.M., CHAKRADHAR, D., “ Prediction and analysis of process failures by ANN classification during wire-EDM of Inconel 718”, Advances in Manufacturing, v. 8, n. 4, pp. 519–536, 2020. doi: https://doi.org/10.1007/s40436-020-00327-w.
» https://doi.org/10.1007/s40436-020-00327-w -
[31] SELVARAJAN, L., RAJAVEL, R., ARUN, C., et al., “Experimental analysis and surface morphology of holes made by electrical discharge machining on MoSi2-SiC composite”, Journal of Materials Engineering and Performance, v. 33, n. 22, pp. 12375–12397, 2023. doi: https://doi.org/10.1007/s11665-023-09000-2.
» https://doi.org/10.1007/s11665-023-09000-2 -
[32] SELVARAJAN, L., SATHIYA NARAYANAN, C., JEYAPAUL, R., “Multi-objective optimization on electric discharge machining using by grey relational analysis”, Applied Mechanics and Materials, v. 592–594, pp. 550-554, 2014. doi: https://doi.org/10.4028/www.scientific.net/AMM.592-594.550.
» https://doi.org/10.4028/www.scientific.net/AMM.592-594.550 -
[33] SELVARAJAN, L., VENKATARAMANAN, K., KANNAN, S., et al., “Surface morphology of silicon nitride (si3n4)-titanium nitride (tin) composites using gra-rsm strategy encompassed with edmed parameters”, Surface Review and Letters, v. 32, n. 11, pp. 2550003, 2025. doi: https://doi.org/10.1142/S0218625X25500039.
» https://doi.org/10.1142/S0218625X25500039 -
[34] GANGIL, M., PRADHAN, M.K., “Optimization the machining parameters by using VIKOR Method during EDM process of Titanium alloy”, Materials Today: Proceedings, v. 5, n. 2, pp. 7486–7495, 2018. doi: https://doi.org/10.1016/j.matpr.2017.11.420.
» https://doi.org/10.1016/j.matpr.2017.11.420 -
[35] JAHAN, A., MUSTAPHA, F., ISMAIL, M.Y., et al., “A comprehensive VIKOR method for material selection”, Materials & Design, v. 32, n. 3, pp. 1215–1221, 2011. doi: https://doi.org/10.1016/j.matdes.2010.10.015.
» https://doi.org/10.1016/j.matdes.2010.10.015 -
[36] KUPPAN, P., NARAYANAN, S., RAJADURAI, A., et al., “Effect of EDM parameters on hole quality characteristics in deep hole drilling of Inconel 718 superalloy”, International Journal of Manufacturing Research, v. 10, n. 1, pp. 45–63, 2015. doi: https://doi.org/10.1504/IJMR.2015.067617.
» https://doi.org/10.1504/IJMR.2015.067617 -
[37] SELVARAJAN, L., MURUGESAN, C.K., KUMAR, S.S., et al., “Comparative analysis of WCu, WC, and BeCu electrodes using Taguchi L18 design for high-performance EDM of additively manufactured AlSi10Mg lattice structures”, Journal of Materials Engineering and Performance, v. 2026, pp. 1–17, 2026. doi: https://doi.org/10.1007/s11665-026-13866-3.
» https://doi.org/10.1007/s11665-026-13866-3 -
[38] VALENTINČIČ, J., BISSACCO, G., TRISTO, G., “Uncertainty of the electrode wear on-machine measurements in micro EDM milling”, Journal of Manufacturing Processes, v. 64, pp. 153–160, 2021. doi: https://doi.org/10.1016/j.jmapro.2021.01.021.
» https://doi.org/10.1016/j.jmapro.2021.01.021 -
[39] RAJ KUMAR, G., SELVARAJAN, L., ARUN, C., et al., “Enhancing multi-response performance of AA2014 hybrid AMMC using TOPSIS algorithm on spark erosion machine”, Metallurgical Research & Technology, v. 122, n. 4, pp. 407, 2025. doi: https://doi.org/10.1051/metal/2025039.
» https://doi.org/10.1051/metal/2025039 -
[40] NGUYEN, M.D., RAHMAN, M., WONG, Y.S., “An experimental study on micro-EDM in low resistivity deionized water using short voltage pulses”, International Journal of Advanced Manufacturing Technology, v. 58, n. 5-8, pp. 533–544, 2012. doi: https://doi.org/10.1007/s00170-011-3397-0.
» https://doi.org/10.1007/s00170-011-3397-0 -
[41] JEYAPRAKASH, N., YANG, C.H., RAJ KUMAR, D., “Minimum cutting thickness and surface roughness achieving during micromachining of aluminium 19000 using CNC machine”, Materials Today: Proceedings, v. 21, pp. 755–761, 2020. doi: https://doi.org/10.1016/j.matpr.2019.06.753.
» https://doi.org/10.1016/j.matpr.2019.06.753 -
[42] DHANABAL, P., KALAYARASAN, M., POOVINAN, A., et al., “Optimized parameters of wire sparking process for machining of AlBe3 Alloy: a step toward enhanced machining performance”, Journal of Materials Engineering and Performance, v. 34, n. 11, pp. 10406–10423, 2025. doi: https://doi.org/10.1007/s11665-024-09790-z.
» https://doi.org/10.1007/s11665-024-09790-z -
[43] NAIR, A., BIZOŃ, W., SKOCZYPIEC, S., et al., “Experimental exploration and optimization of dual-channel electrode micro-drilling in Inconel 617 using electrical discharge machining”, Journal of the Brazilian Society of Mechanical Sciences and Engineering, v. 46, n. 11, pp. 673, 2024. doi: https://doi.org/10.1007/s40430-024-05247-5.
» https://doi.org/10.1007/s40430-024-05247-5 -
[44] ZHANG, J., HAN, F., “Rotating short arc EDM milling method under composite energy field”, Journal of Manufacturing Processes, v. 64, pp. 805–815, 2021. doi: https://doi.org/10.1016/j.jmapro.2021.01.049.
» https://doi.org/10.1016/j.jmapro.2021.01.049 -
[45] SELVARAJAN, L., PRAKASH, B., ARUN, C., et al., “Comparative performance evaluation of Cu, brass, graphite, W-Cu, and W-C electrodes in EDM of Si3N4-TiN composites using hybrid ai-based optimization algorithms”, Journal of Materials Engineering and Performance, v. 2026, n. 26, pp. 1–16, 2026. doi: https://doi.org/10.1007/s11665-026-13566-y.
» https://doi.org/10.1007/s11665-026-13566-y -
[46] SELVARAJAN, L., ARUN, C., BORAH, J., “Enhancing machining performance of AlSi10Mg composites using EDM: a Taguchi-RSM-random forest approach”, Metallurgical Research & Technology, v. 123, n. 3, pp. 302, 2026. doi: https://doi.org/10.1051/metal/2025132.
» https://doi.org/10.1051/metal/2025132














